- Highly selective reduction of nitroarenes to anilines catalyzed using MOF-derived hollow Co3S4 in water under ambient conditions
-
We developed a new strategy for the efficient reduction of nitroarenes using sodium sulfide as reducing agent with MOF-derived Co3S4 as catalyst in water and at room temperature. The introduction of sodium sulfite enhanced the reactant conversion and product selectivity, and the as-synthesized catalyst was used repeatedly five times and retained its activity and selectivity. A wide spectrum of reducible functional moieties kept unaffected under the reaction conditions, and isotope labeling experiment showed the hydrogen atom was derived from water.
- Xu, Yong,Lv, Xiao-Jun,Chen, Yong,Fu, Wen-Fu
-
-
Read Online
- Indium as a reducing agent: Reduction of aromatic nitro groups
-
Treatment of a range of aromatic nitro compounds with indium powder in aqueous ethanolic ammonium chloride results in selective reduction of the nitro groups; ester, nitrile, amide and halide substituents are unaffected.
- Moody, Christopher J.,Pitts, Michael R.
-
-
Read Online
- Catalytic hydrogenation of sulfur-containing nitrobenzene over Pd/C catalysts: In situ sulfidation of Pd/C for the preparation of PdxSy catalysts
-
The preparation of supported palladium sulfides catalysts has attracted much attention due to their good sulfur-resistant properties in the hydrogenation of sulfur-containing compounds. In this work, we unambiguously demonstrated that Pd/C catalyst could be in situ sulfided by organic sulfur-containing reactant molecules and the sulfidation was highly dependent on temperature. The in situ sulfidation of Pd/C catalyst was composed of a reaction of Pd with the sulfur derived from the cleavage of C-S bond of sulfur-containing reactant molecules, followed by a transformation to PdxSy at high temperatures (around 120 °C). The sulfided Pd/C catalyst could be used for at least 18 recycles without a significant loss in its activity during the hydrogenation of sulfur-containing nitrobenzene at 180 °C with 3 MPa H2, which could be attributed to the stable presence of Pd4S and Pd16S7.
- Zhang, Qunfeng,Xu, Wei,Li, Xiaonian,Jiang, Dahao,Xiang, Yizhi,Wang, Jianguo,Cen, Jie,Romano, Stephen,Ni, Jun
-
-
Read Online
- Chemoselective nitro reduction and hydroamination using a single iron catalyst
-
The reduction and reductive addition (formal hydroamination) of functionalised nitroarenes is reported using a simple and bench-stable iron(iii) catalyst and silane. The reduction is chemoselective for nitro groups over an array of reactive functionalities (ketone, ester, amide, nitrile, sulfonyl and aryl halide). The high activity of this earth-abundant metal catalyst also facilitates a follow-on reaction in the reductive addition of nitroarenes to alkenes, giving efficient formal hydroamination of olefins under mild conditions. Both reactions offer significant improvements in catalytic activity and chemoselectivity and the utility of these catalysts in facilitating two challenging reactions supports an important mechanistic overlap.
- Zhu, Kailong,Shaver, Michael P.,Thomas, Stephen P.
-
-
Read Online
- Hexafluoro-2-propanol-assisted quick and chemoselective nitro reduction using iron powder as catalyst under mild conditions
-
Hexafluoro-2-propanol as the promoter for the quick nitro reduction using a combination of iron powder and 2 N HCl aqueous solution is reported. This methodology has several positive features, as it is of room temperature, remarkably short reaction time. A wide range of substrates including those bearing reducible functional groups such as aldehyde, ketone, acid, ester, amide, nitrile, halogens, even allyl, propargyl and heterocycles are chemoselectively reduced in good to excellent yields, even on gram scale. Notably, the highly selective reduction of 3-nitrophenylboronic acid is achieved quantitatively. The reduction is also tolerant of common protecting groups, and aliphatic nitro compound, 1-nitrooctane can be reduced successfully.
- Chen, Xu-Ling,Ai, Bai-Ru,Dong, Yu,Zhang, Xiao-Mei,Wang, Ji-Yu
-
-
Read Online
- The synergic effects at the molecular level in CoS2 for selective hydrogenation of nitroarenes
-
Catalytic functionalized aniline formation from nitroarenes is a core technology in the synthesis of pharmaceuticals, agrochemicals, and fine chemicals. However, control of chemoselectivity still poses particular challenges with aromatic nitro substrates bearing one or more reducible groups. Here, we report the low-cost synthesis of a porous carbon supported CoS2 catalyst (CoS2/PC) and successfully apply the catalyst in the chemoselective hydrogenation of nitroarenes. For hydrogenation of 3-nitrostyrene, the catalyst furnishes a superior selectivity of 99% towards 3-aminostyrene at a conversion of >99%. Density functional theory calculations together with X-ray absorption fine structure spectroscopy reveal that terdentate and tetrahedral coordinated Co atoms in CoS2 (labeled as Co3 and Co4) are possible active sites. The face to face located Co3 and Co4 sites make the reaction rather local, and Co3 and Co4 sites are occupied by substrates and H2, respectively, which is beneficial to the superior activity and selectivity. The Co3-Co4 "synergic active site pair" in CoS2 makes the investigation of the synergic effects at the molecular level a reality on heterogeneous catalysts.
- Wei, Zhongzhe,Mao, Shanjun,Sun, Fanfei,Wang, Jing,Mei, Bingbao,Chen, Yiqing,Li, Haoran,Wang, Yong
-
-
Read Online
- Shape Engineering of Biomass-Derived Nanoparticles from Hollow Spheres to Bowls through Solvent-Induced Buckling
-
The realization of asymmetric hollow carbonaceous nanostructures remains a great challenge, especially when biomass is chosen as the carbon resource through hydrothermal carbonization (HTC). Herein, a simple and straightforward solvent-induced buckling strategy is demonstrated for the synthesis of asymmetric spherical and bowl-like carbonaceous nanomaterials. The formation of the bowl-like morphology was attributed to the buckling of the spherical shells induced by the dissolution of the oligomers. The bowl-like particles prepared through this solvent-driven approach demonstrated a well-controlled morphology and a uniform particle size of approximately 360 nm. The obtained nanospheres and nanobowls were loaded with CoS2 nanoparticles to act as heterogeneous catalysts for the selective hydrogenation of aromatic nitro compounds. As expected, the CoS2/nanobowls catalyst showed good tolerance to a wide scope of reducible groups and afforded both high activity and selectivity in almost all the tested substrates.
- Chen, Chunhong,Li, Xuefeng,Deng, Jiang,Wang, Zhe,Wang, Yong
-
-
Read Online
- In Situ-Generated Co0-Co3O4/N-Doped Carbon Nanotubes Hybrids as Efficient and Chemoselective Catalysts for Hydrogenation of Nitroarenes
-
The earth-abundant nanohybrids Co0/Co3O4@N-doped carbon nanotubes were fabricated via an efficient thermal condensation of d-glucosamine hydrochloride, melamine, and Co(NO3)2·6H2O. The hybrids furnish excellent catalytic activity and perfect chemoselectivity (>99%) for a wide range of substituted nitroarenes (21 examples) under relatively mild conditions. The high catalytic performance and durability is attributed to the synergistic effects between each component, the unique structure of graphene layers-coated Co0, and the electronic activation of doped nitrogen. Density functional calculations indicate that the inner Co0 core and N species on the carbon shell can significantly decrease the dissociation energies of H2, giving evidence of the ability of carbon shell in the hybrids to enable H2 activation. These results open up an avenue to design more powerful low-cost catalysts for industrial applications.
- Wei, Zhongzhe,Wang, Jing,Mao, Shanjun,Su, Diefeng,Jin, Haiyan,Wang, Yihe,Xu, Fan,Li, Haoran,Wang, Yong
-
-
Read Online
- Reduction of nitroarenes using CO and H2O in the presence of a nanostructured cobalt oxide/Nitrogen-Doped Graphene (NGr) catalyst
-
The most common route to anilines is based on the reduction of the corresponding nitroarenes. In general, hydrogen is preferred as reducing agent and numerous catalytic systems are known to achieve such transformations. Besides, the use of CO/H2O as hydrogen source offers interesting possibilities for reductions. Carbon monoxide is a cheap and abundant chemical used on industrial scale for a variety of transformations. Although the reduction of nitroarenes with CO/H2O is known in the presence of noble-metal catalysts, earth-abundant inexpensive catalysts showing high selectivity have not yet been developed. In this respect, herein we present the use of a heterogeneous cobalt oxide catalyst (Co3O4/NGr@C), which is modified by nitrogen-doped graphene layers. Using this non-noble metal catalyst nitroarenes are reduced in high yields and good chemoselectivities.
- Westerhaus, Felix A.,Sorribes, Ivn,Wienh?fer, Gerrit,Junge, Kathrin,Beller, Matthias
-
-
Read Online
- A sulfur-tolerant phosphorus doped Pd/C catalyst for hydrogenation of 4-nitrothioanisole
-
In this paper, we report a new type of sulfur resistant hydrogenation catalyst, which was obtained by simply phosphating commercial Pd/C catalyst with triphenylphosphine under H2 atmosphere at 600 °C. At this temperature, no palladium phosphides formed in XRD patterns due to the low synthetic temperature. Element analysis, N2 adsorption-desorption and ICP characterizations show that only a small amount of P has been introduced into Pd, so the phosphorus doping does not change the pore size and surface area of pristine Pd/C. XPS characterization shows that P doping can effectively prevent the substrate adsorption on Pd surface, which relieves the sulfurization rate of Pd. Hence, the phosphorus doping catalyst can fully catalyze the 4-nitrothioanisole to 4-aminothioanisole and exhibits higher activity than Pd/C, which only has 70.9 % conversion. Moreover, the phosphorus doped Pd/C catalyst has better stability than Pd/C and its activity is almost unchanged during the recycle.
- Xiong, Renjie,Zhao, Wenqiang,Wang, Zhiqiang,Zhang, Minghui
-
-
Read Online
- General and selective iron-catalyzed transfer hydrogenation of nitroarenes without base
-
The first well-defined iron-based catalyst system for the reduction of nitroarenes to anilines has been developed applying formic acid as reducing agent. A broad range of substrates including other reducible functional groups were converted to the corresponding anilines in good to excellent yields at mild conditions. Notably, the process constitutes a rare example of base-free transfer hydrogenations.
- Wienhoefer, Gerrit,Sorribes, Ivan,Boddien, Albert,Westerhaus, Felix,Junge, Kathrin,Junge, Henrik,Llusar, Rosa,Beller, Matthias
-
-
Read Online
- Commercially Available CuO Catalyzed Hydrogenation of Nitroarenes Using Ammonia Borane as a Hydrogen Source
-
Tandem ammonia borane dehydrogenation and nitroarenes hydrogenation has been reported as a novel strategy for the preparation of aromatic amines. However, the practical application of this strategy is subjected to the high-cost and tedious preparation of supported noble metal nanocatalysts. The commercially available CuO powder is herein demonstrated to be a robust catalyst for hydrogenation of nitroarenes using ammonia borane as a hydrogen source under mild conditions. Numerous amines (even sterically hindered, halogenated, and diamines) could be obtained through this method. This monometallic catalyst is characteristic of support-free, excellent chemoselectivity, low-cost, and high recyclability, which will favor its future utilization in preparative reduction chemistry. Mechanistic studies are also carried out to clarify that diazene and azoxybenzene are key intermediates of this heterogeneous reduction.
- Du, Jialei,Chen, Jie,Xia, Hehuan,Zhao, Yiwei,Wang, Fang,Liu, Hong,Zhou, Weijia,Wang, Bin
-
-
Read Online
- Pd/C-catalyzed transfer hydrogenation of aromatic nitro compounds using methanol as a hydrogen source
-
We describe the selective transfer hydrogenation of aromatic nitro compounds to anilines using Pd/C as a heterogeneous catalyst with methanol as a green reductant. Nitroarenes bearing both electron-releasing and electron-deficient groups are amenable to this method and enable the synthesis of corresponding arylamines in moderate to good selectivities including the synthesis of butamben, a local anesthictic drug molecule. This new concise protocol is simple, ligand-free and does not require the supply of external molecular hydrogen.
- Goyal, Vishakha,Sarki, Naina,Natte, Kishore,Ray, Anjan
-
-
Read Online
- Defect-mediated selective hydrogenation of nitroarenes on nanostructured WS2
-
Transition metal dichalcogenides (TMDs) are well known catalysts as both bulk and nanoscale materials. Two-dimensional (2-D) TMDs, which contain single- and few-layer nanosheets, are increasingly studied as catalytic materials because of their unique thickness-dependent properties and high surface areas. Here, colloidal 2H-WS2 nanostructures are used as a model 2-D TMD system to understand how high catalytic activity and selectivity can be achieved for useful organic transformations. Free-standing, colloidal 2H-WS2 nanostructures containing few-layer nanosheets are shown to catalyze the selective hydrogenation of a broad scope of substituted nitroarenes to their corresponding aniline derivatives in the presence of other reducible functional groups. Microscopic and computational studies reveal the important roles of sulfur vacancy-rich basal planes and tungsten-terminated edges, which are more abundant in nanostructured 2-D materials than in their bulk counterparts, in enabling the functional group selectivity. At tungsten-terminated edges and on regions of the basal planes having high concentrations of sulfur vacancies, vertical adsorption of the nitroarene is favored, thus facilitating hydrogen transfer exclusively to the nitro group due to geometric effects. At lower sulfur vacancy concentrations on the basal planes, parallel adsorption of the nitroarene is favored, and the nitro group is selectively hydrogenated due to a lower kinetic barrier. These mechanistic insights reveal how the various defect structures and configurations on 2-D TMD nanostructures facilitate functional group selectivity through distinct mechanisms that depend upon the adsorption geometry, which may have important implications for the design of new and enhanced 2-D catalytic materials across a potentially broad scope of reactions.
- Sun, Yifan,Darling, Albert J.,Li, Yawei,Fujisawa, Kazunori,Holder, Cameron F.,Liu, He,Janik, Michael J.,Terrones, Mauricio,Schaak, Raymond E.
-
-
Read Online
- Selective Reduction of Nitroarenes with Silanes Catalyzed by Nickel N-Heterocyclic Carbene Complexes
-
An efficient catalytic system for the reduction of nitroarenes to amines was developed using a well-defined nickel–NHC (N-heterocyclic carbene) complex as catalyst and phenylsilane as reducing agent. The excellent activity of the catalyst provides access to anilines containing a wide array of reactive functionalities at 20 °C, and without using any base or additive. Notably, the catalytic system allows the reduction of 5,10,15,20-tetra-(nitrophenyl)porphyrin (TNPP) and CuII β-nitroporphyrin to the corresponding aminoporphyrins.
- Lopes, Rita,Pereira, Mariette M.,Royo, Beatriz
-
-
Read Online
- Heterogenized cobalt oxide catalysts for nitroarene reduction by pyrolysis of molecularly defined complexes
-
Molecularly well-defined homogeneous catalysts are known for a wide variety of chemical transformations. The effect of small changes in molecular structure can be studied in detail and used to optimize many processes. However, many industrial processes require heterogeneous catalysts because of their stability, ease of separation and recyclability, but these are more difficult to control on a molecular level. Here, we describe the conversion of homogeneous cobalt complexes into heterogeneous cobalt oxide catalysts via immobilization and pyrolysis on activated carbon. The catalysts thus produced are useful for the industrially important reduction of nitroarenes to anilines. The ligand indirectly controls the selectivity and activity of the recyclable catalyst and catalyst optimization can be performed at the level of the solution-phase precursor before conversion into the active heterogeneous catalyst.
- Westerhaus, Felix A.,Jagadeesh, Rajenahally V.,Wienhoefer, Gerrit,Pohl, Marga-Martina,Radnik, Joerg,Surkus, Annette-Enrica,Rabeah, Jabor,Junge, Kathrin,Junge, Henrik,Nielsen, Martin,Brueckner, Angelika,Beller, Matthias
-
-
Read Online
- Simple and chemoselective reduction of aromatic nitro compounds to aromatic amines: Reduction with hydriodic acid revisited
-
Reduction of aromatic nitro compounds to amines with hydriodic acid was reinvestigated. Under a milder non-refluxing condition (at 90°C for 2-4 h), the reduction proceeded efficiently with excellent chemoselectivity without affecting other functional groups including nitrile, ester, halide, carbonyl, amide, sulfonamide, imidazole and methylthio groups.
- Kumar, J.S.Dileep,Ho, ManKit M.,Toyokuni, Tatsushi
-
-
Read Online
- Novel protocol for synthesis of 1,4-diiminocurcumin stabilized silver nanoparticles and application as heterogenous recyclable catalyst and antibacterial agent
-
Abstract: Curcumin [(1E, 6E)-1,7-bis(4-hydroxy-3-methoxy-phenyl)-1,6-heptadiene-3,5-dione] is a low molecular weight yellow-orange polyphenolic pigment extracted from the powdered rhizome of Curcuma longa. Curcumin has wide medicinal applications as an antioxidant, anti-inflammatory, cancer chemopreventive, and potentially chemotherapeutic agents as well as stabilizer/reducing agent in silver nanoparticles (AgNPs) synthesis. However, the low solubility of curcumin in aqueous solutions limits its applications and also, many of AgNP synthetic processes lack a greener synthetic route. In the present work, a Schiff base of curcumin is synthesized condensing curcumin and 1,4-diaminobutane in 2:1 ratio. The resulting product shows improvement in solubility in water and favours the synthesis of AgNPs in aqueous medium at room temperature, acting as a self-reducing/stabilizing agent. This proposed synthetic route is simple, feasible and green. The size and morphology of AgNPs are analyzed by TEM, SEM, EDS and XRD techniques. The recyclable AgNPs as a heterogeneous catalyst in the reduction of nitroaromatics to amino compounds is environmentally benign and can be re-used up to 5th cycle without considerable loss of its catalytic activity. Moreover, both Cur-1,4 and AgNPs show bactericidal properties against bacterial strains (Bacillus subtilis, Staphylococcus aureus, Escherichia coli and Pseudomonas aeruginosa) which find medicinal importance in future. Graphic abstract: A greener approach has been proposed for the preparation of AgNPs stabilized on curcumin based Schiff base. The AgNPs finds applications as efficient, easily recyclable heterogenous catalyst in the reduction of nitroaromatics to environmentally benign aminoaromatics as well as an antibacterial agent.[Figure not available: see fulltext.].
- Gogoi, Nishi Gandha,Handique, Jyotirekha G
-
-
Read Online
- Chemoselective transfer hydrogenation to nitroarenes mediated by cubane-type Mo3S4 cluster catalysts
-
Chemoselective cubes: Cubane-type [Mo3S4X 3(dmpe)3]+ clusters (dmpe=1,2-(bis) dimethylphosphinoethane), in combination with an azeotropic 5:2 mixture of HCOOH and NEt3 as the reducing agent, act as selective cluster catalysts (X=H) or precatalysts (X=Cl) for the transfer hydrogenation of functionalized nitroarenes, without the formation of hazardous hydroxylamines. Copyright
- Sorribes, Iván,Wienh?fer, Gerrit,Vicent, Cristian,Junge, Kathrin,Llusar, Rosa,Beller, Matthias
-
-
Read Online
- Metal–Organic-Framework-Derived Co3S4 Hollow Nanoboxes for the Selective Reduction of Nitroarenes
-
MOF-derived Co3S4/CN hollow nanoboxes (CN=nitrogen-doped carbon) was used to catalyze the chemoselective reduction of nitroarenes to anilines under mild reaction conditions with H2 as the reducing agent. The catalyst provides high conversion efficiencies and selectivities for a variety of nitroarene substrates that contain electron-donating or electron-withdrawing substituents under mild reaction conditions (in methanol at 60 °C). Further, the nanobox inhibits both dehalogenation and vinyl hydrogenation reactions, which are common limitations of state-of-the-art Pd-based catalysts. Because the reactions result in pure aniline products, the need for separation by column chromatography is eliminated. The resulting anilines are easily separated from the methanolic reaction solution in just three simple steps (centrifugation, decantation, and drying). If employed in industrial processes, catalysts of this kind would significantly reduce the amount of waste organic solvent generated and thus satisfy the need for sustainable chemical processes.
- Yang, Shuliang,Peng, Li,Sun, Daniel T.,Oveisi, Emad,Bulut, Safak,Queen, Wendy L.
-
-
Read Online
- A Mild Heteroatom (O -, N -, and S -) Methylation Protocol Using Trimethyl Phosphate (TMP)-Ca(OH) 2Combination
-
A mild heteroatom methylation protocol using trimethyl phosphate (TMP)-Ca(OH)2combination has been developed, which proceeds in DMF, or water, or under neat conditions, at 80 °C or at room temperature. A series of O-, N-, and S-nucleophiles, including phenols, sulfonamides, N-heterocycles, such as 9H-carbazole, indole derivatives, and 1,8-naphthalimide, and aryl/alkyl thiols, are suitable substrates for this protocol. The high efficiency, operational simplicity, scalability, cost-efficiency, and environmentally friendly nature of this protocol make it an attractive alternative to the conventional base-promoted heteroatom methylation procedures.
- Tang, Yu,Yu, Biao
-
-
- Method for preparing amine through catalytic reduction of nitro compound by cyclic (alkyl) (amino) carbene chromium complex
-
The cyclic (alkyl) (amino) carbene chromium complex is prepared from corresponding ligand salt, alkali and CrCl3 and used for catalyzing pinacol borane to reduce nitro compounds in an ether solvent under mild conditions to generate corresponding amine. The method for preparing amine has the advantages of cheap and accessible raw materials, mild reaction conditions, wide substrate application range, high selectivity and the like, and is simple to operate.
- -
-
Paragraph 0015
(2021/04/17)
-
- Chemoselective Hydrogenation of Nitroarenes Using an Air-Stable Base-Metal Catalyst
-
The reduction of nitroarenes to anilines as well as azobenzenes to hydrazobenzenes using a single base-metal catalyst is reported. The hydrogenation reactions are performed with an air-and moisture-stable manganese catalyst and proceed under relatively mild reaction conditions. The transformation tolerates a broad range of functional groups, affording aniline derivatives and hydrazobenzenes in high yields. Mechanistic studies suggest that the reaction proceeds via a bifunctional activation involving metal-ligand cooperative catalysis.
- Zubar, Viktoriia,Dewanji, Abhishek,Rueping, Magnus
-
supporting information
p. 2742 - 2747
(2021/05/05)
-
- Rhodium-terpyridine Catalyzed Transfer Hydrogenation of Aromatic Nitro Compounds in Water
-
A rhodium terpyridine complex catalyzed transfer hydrogenation of nitroarenes to anilines with i-PrOH as hydrogen source and water as solvent has been developed. The catalytic system can work at a substrate/catalyst (S/C) ratio of 2000, with a turnover frequency (TOF) up to 3360 h?1, which represents one of the most active catalytic transfer hydrogenation systems for nitroarene reduction. The catalytic system is operationally simple and the protocol could be scaled up to 20 gram scale. The water-soluble catalyst bearing a carboxyl group could be recycled 15 times without significant loss of activity.
- Liu, Yuxuan,Miao, Wang,Tang, Weijun,Xue, Dong,Xiao, Jianliang,Wang, Chao,Li, Changzhi
-
supporting information
p. 1725 - 1729
(2021/06/01)
-
- Cyclic (Alkyl)(amino)carbene Ligand-Promoted Nitro Deoxygenative Hydroboration with Chromium Catalysis: Scope, Mechanism, and Applications
-
Transition metal catalysis that utilizes N-heterocyclic carbenes as noninnocent ligands in promoting transformations has not been well studied. We report here a cyclic (alkyl)(amino)carbene (CAAC) ligand-promoted nitro deoxygenative hydroboration with cost-effective chromium catalysis. Using 1 mol % of CAAC-Cr precatalyst, the addition of HBpin to nitro scaffolds leads to deoxygenation, allowing for the retention of various reducible functionalities and the compatibility of sensitive groups toward hydroboration, thereby providing a mild, chemoselective, and facile strategy to form anilines, as well as heteroaryl and aliphatic amine derivatives, with broad scope and particularly high turnover numbers (up to 1.8 × 106). Mechanistic studies, based on theoretical calculations, indicate that the CAAC ligand plays an important role in promoting polarity reversal of hydride of HBpin; it serves as an H-shuttle to facilitate deoxygenative hydroboration. The preparation of several commercially available pharmaceuticals by means of this strategy highlights its potential application in medicinal chemistry.
- Zhao, Lixing,Hu, Chenyang,Cong, Xuefeng,Deng, Gongda,Liu, Liu Leo,Luo, Meiming,Zeng, Xiaoming
-
supporting information
p. 1618 - 1629
(2021/01/25)
-
- Copper nanoparticles (CuNPs) catalyzed chemoselective reduction of nitroarenes in aqueous medium
-
Abstract: A procedure for practical synthesis of CuNPs from CuSO4·5H2O is established, under appropriate reaction conditions, using rice (Oryza sativa) as an economic source of reducing as well as a stabilizing agent. Optical and microscopic techniques are employed for the characterization of the synthesized CuNPs and the sizes of the particles were found to be in the range of 8 ± 2 nm. The nanoparticles are used as a catalyst for chemoselective reduction of aromatic nitro compounds to corresponding amines under ambient conditions and water as a reaction medium. Graphic abstract: CuNPs are synthesized using hydrolysed rice and used as catalyst for chemoselective reduction of nitroarenes to their corresponding amines in water. [Figure not available: see fulltext.]
- Chand, Dillip Kumar,Rai, Randhir
-
-
- Chemoselective electrochemical reduction of nitroarenes with gaseous ammonia
-
Valuable aromatic nitrogen compounds can be synthesized by reduction of nitroarenes. Herein, we report electrochemical reduction of nitroarenes by a protocol that uses inert graphite felt as electrodes and ammonia as a reductant. Depending on the cell voltage and the solvent, the protocol can be used to obtain aromatic azoxy, azo, and hydrazo compounds, as well as aniline derivatives with high chemoselectivities. The protocol can be readily scaled up to >10 g with no decrease in yield, demonstrating its potential synthetic utility. A stepwise cathodic reduction pathway was proposed to account for the generations of products in turn.
- Chang, Liu,Li, Jin,Wu, Na,Cheng, Xu
-
supporting information
p. 2468 - 2472
(2021/04/02)
-
- CoPd Nanoalloys with Metal–Organic Framework as Template for Both N-Doped Carbon and Cobalt Precursor: Efficient and Robust Catalysts for Hydrogenation Reactions
-
In this work, a series of metal–organic framework (MOF)-derived CoPd nanoalloys have been prepared. The nanocatalysts exhibited excellent activities in the hydrogenation of nitroarenes and alkenes in green solvent (ethanol/water) under mild conditions (H2 balloon, room temperature). Using ZIF-67 as template for both carbon matrix and cobalt precursor coating with a mesoporous SiO2 layer, the catalyst CoPd/NC@SiO2 was smoothly constructed. Catalytic results revealed a synergistic effect between Co and Pd components in the hydrogenation process due to the enhanced electron density. The mesoporous SiO2 shell effectively prevented the sintering of hollow carbon and metal NPs at high temperature, furnishing the well-dispersed nanoalloy catalysts and better catalytic performance. Moreover, the catalyst was durable and showed negligible activity decay in recycling and scale-up experiments, providing a mild and highly efficient way to access amines and arenes.
- Zhu, Jie,Xu, Deng,Ding, Lu-jia,Wang, Peng-cheng
-
p. 2707 - 2716
(2021/01/21)
-
- Cobalt nanoclusters coated with N-doped carbon for chemoselective nitroarene hydrogenation and tandem reactions in water
-
The development of active and selective non-noble metal-based catalysts for the chemoselective reduction of nitro compounds in aquo media under mild conditions is an attractive research area. Herein, the synthesis of subnanometric and stable cobalt nanoclusters, covered by N-doped carbon layers as core-shell (Co@NC-800), for the chemoselective reduction of nitroarenes is reported. TheCo@NC-800catalyst was prepared by the pyrolysis of the Co(tpy)2complex impregnated on Vulcan carbon. In fact, the use of a molecular complex based on six N-Co bonds drives the formation of a well-defined and distributed cobalt core-shell nanocluster covered by N-doped carbon layers. In order to elucidate its nature, it has been fully characterized by using several advanced techniques. In addition, this as-prepared catalyst showed high activity, chemoselectivity and stability toward the reduction of nitro compounds with H2and under mild reaction conditions; water was used as a green solvent, improving the previous results based on cobalt catalysts. Moreover, theCo@NC-800catalyst is also active and selective for the one-pot synthesis of secondary aryl amines and isoindolinones through the reductive amination of nitroarenes. Finally, based on diffraction and spectroscopic studies, metallic cobalt nanoclusters with surface CoNxpatches have been proposed as the active phase in theCo@NC-800material.
- Agostini, Giovanni,Calvino, Jose. J.,Corma, Avelino,Gutiérrez-Tarri?o, Silvia,Lopes, Christian W.,O?a-Burgos, Pascual,Rojas-Buzo, Sergio
-
supporting information
p. 4490 - 4501
(2021/06/28)
-
- High yielding electrophilic amination with lower order and?higher order organocuprates: Application of acetone O-(4-Chlorophenylsulfonyl)oxime in the construction of the C?N bond at room temperature
-
Electrophilic amination reaction was performed with lower order and?higher order organocuprates using acetone O-(4-Chlorophenylsulfonyl)oxime (1). It was proceeded smoothly at room temperature in the presence of organocuprates to provide the corresponding primary amines in good yields with 10 and 60 min, respectively. The primary amine yields of the electrophilic amination of bromomagnesium organocyanocuprates and dibromomagnesium diorganocyanocuprates were obtained 52–72% and 58–83%, respectively. We observed that higher order organocuprates were more successful than lower order organocuprates in the synthesis of functionalized arylamines by electrophilic amination.
- Duran, Serdar,Korkmaz, Adem
-
p. 2077 - 2087
(2021/05/27)
-
- Selective Carbon-Carbon Bond Amination with Redox-Active Aminating Reagents: A Direct Approach to Anilines?
-
Amines are among the most fundamental motifs in chemical synthesis, and the introduction of amine building blocks via selective C—C bond cleavage allows the construction of nitrogen compounds from simple hydrocarbons through direct skeleton modification. Herein, we report a novel method for the preparation of anilines from alkylarenes via Schmidt-type rearrangement using redox-active amination reagents, which are easily prepared from hydroxylamine. Primary amines and secondary amines were prepared from corresponding alkylarenes or benzyl alcohols under mild conditions. Good compatibility and valuable applications of the transformation were also displayed.
- Qiu, Xu,Wang, Yachong,Su, Lingyu,Jin, Rui,Song, Song,Qin, Qixue,Li, Junhua,Zong, Baoning,Jiao, Ning
-
p. 3011 - 3016
(2021/09/13)
-
- Room-temperature copper-catalyzed electrophilic amination of arylcadmium iodides with ketoximes
-
We started our study by preparation two ketoximes. Later, there were studies to reveal these ketoximes' effects in the electrophilic amination reaction with organocadmium reagents. Primarily, it was observed that arylcadmium iodides could not be reacted with ketoximes at room temperature in the absence of a catalyst. CuCN was a suitable catalyst for this electrophilic amination reaction of arylcadmium iodides and allowed the preparation of functionalized aniline derivatives in good yields under mild reaction conditions. We obtained the results indicated that the yield of primary arylamines was strongly dependent on the steric and electronic effects of organocadmium reagent and amination agent. In the case of both amination reagents, meta-substituted arylamines were obtained in higher yields than para-substituted arylamines. We observed that acetone O-(4-chlorophenylsulfonyl)oxime, 1, as an aminating agent, was more successful than acetone O-(2-Naphthylsulfonyl)oxime, 2, in the synthesis of functionalized arylamines by electrophilic amination of corresponding aryl cadmium iodides. In this method, there is no cadmium release to the environment.
- Korkmaz, Adem
-
p. 3119 - 3125
(2021/05/10)
-
- Method for synthesizing heteroatom- substituted aromatic compound from styrene compound
-
The invention discloses a method for synthesizing a heteroatom-substituted aromatic compound from a styrene compound, which comprises the following steps of: mixing a styrene compound with a general formula (I) and a heteroatom-containing compound with a general formula (II), and reacting in the presence of an acid additive and an organic solvent to obtain a heteroatom-substituted compound with ageneral formula (III). According to the synthesis method disclosed by the invention, a large amount of styrene compounds are used as raw materials and react to generate aromatic amine or phenol compounds under the action of no metal catalysis; and compared with the traditional aromatic amine and phenol synthesis method, the method has the advantages of high yield, simple conditions, low waste discharge amount, no metal participation, simple reaction equipment, easiness in industrial production and the like.
- -
-
Paragraph 0169-0172
(2021/02/06)
-
- Copper-Catalyzed Methylthiolation of Aryl Iodides and Bromides with Dimethyl Disulfide in Water
-
An efficient route to aryl methyl sulfides through the copper-catalyzed coupling reaction of aryl iodides or bromides with dimethyl disulfide in water is described. Electron-donating and electron-withdrawing functional groups in the substrates were tolerated, and the corresponding products were obtained in moderate to good yields.
- Wang, Ying-Yu,Wu, Xiang-Mei,Yang, Ming-Hua
-
supporting information
(2020/07/20)
-
- Palladium supported on metal–organic framework as a catalyst for the hydrogenation of nitroarenes under mild conditions
-
Sustainable development demands an environmentally friendly and efficient method for the hydrogenation of organic molecules, including the hydrogenation of functionalized nitroarenes. In this study, a highly active and selective metal–organic framework-supported palladium catalyst was prepared for the catalytic hydrogenation of nitroarenes. High selectivity (>99%) and excellent yield (98%) of aniline were realized after 2 hours in ethanol under hydrogen (1 atm) at room temperature. The reductions were successfully carried out in the presence of a wide range of other reducible functional groups. More importantly, the catalyst was very stable without the loss of its catalytic activity after five cycles.
- Bao, Lingxiang,Fei, Teng,Li, Jiazhe,Pang, Siping,Sun, Chenghui,Yan, Zhiyuan,Yu, Zongbao
-
-
- Method for reducing aromatic nitro compounds into aromatic amine compounds
-
The invention discloses a method for reducing aromatic nitro compounds into aromatic amine compounds. The aromatic nitro compounds are reacted at a temperature of 110-130 DEG C in an inert or air atmosphere under the action of a rhodium catalyst by using water as a solvent, isopropanol as a hydrogen source and potassium phosphate or sodium carbonate as an alkali to obtain the aromatic amine compounds. The method has the advantages of simplicity in operation, greenness, environmental friendliness, reduction of environmental pollution, high reaction yield, amplified gram-scale preparation of theamine compounds, high catalyst activity, recyclability and low industrial production cost.
- -
-
Paragraph 0020-0021
(2020/03/25)
-
- Electrochemical and direct C-H methylthiolation of electron-rich aromatics
-
The electrochemical-induced C-H methylthiolation of electron-rich aromatics has been accomplished via a three component cross-coupling strategy. Potassium thiocyanate (KSCN) as both the supporting electrolyte and sulfur source and methanol as the methylation reagent are used. This protocol is versatile for various (hetero)aromatic compounds such as aniline, anisole and indole. The reaction proceeds under mild conditions without any metal catalyst, exogenous oxidant and highly toxic sulfur reagent. Importantly, such an electrochemical-induced methylthiolated reaction could be easily scaled up with good efficiency.
- Wu, Yaxing,Ding, Hongliang,Zhao, Ming,Ni, Zhong-Hai,Cao, Jing-Pei
-
supporting information
p. 4906 - 4911
(2020/08/25)
-
- EffectiveN-methylation of nitroarenes with methanol catalyzed by a functionalized NHC-based iridium catalyst: a green approach toN-methyl amines
-
Compound [IrBr(CO)2(κC-tBuImCH2PyCH2OMe)] featuring a flexible pyridine/OMe functionalized NHC ligand κ1C coordinated efficiently catalyzes the selectiveN-monomethylation of nitroarenes using methanol as both the reducing agent and the C1 source. A range of functionalized nitroarenes including heterocyclic or sterically hindered derivatives have been efficiently converted to the correspondingN-monomethyl amines in good yields at low catalyst loadings using sub-stoichiometric amounts of Cs2CO3as a base. Mechanistic investigations support a borrowing-hydrogen mechanism in which methanol acts as the hydrogen source and methylating agent. Further, the hydrogen transfer reduction of nitrobenzene to aniline under optimized reaction conditions should proceed through a direct mechanism involving nitrosobenzene andN-phenylhydroxylamine intermediates.
- González-Lainez, Miguel,Jiménez, M. Victoria,Passarelli, Vincenzo,Pérez-Torrente, Jesús J.
-
p. 3458 - 3467
(2020/06/17)
-
- Oxalic amide ligands, and uses thereof in copper-catalyzed coupling reaction of aryl halides
-
The present invention provides oxalic amide ligands and uses thereof in copper-catalyzed coupling reaction of aryl halides. Specifically, the present invention provides a use of a compound represented by formula I, wherein definitions of each group are described in the specification. The compound represented by formula I can be used as a ligand in copper-catalyzed coupling reaction of aryl halides for the formation of C—N, C—O and C—S bonds.
- -
-
Page/Page column 89-90
(2020/01/09)
-
- HETEROCYCLIC CARBOXYLIC ACID AMIDE LIGAND AND APPLICATIONS THEREOF IN COPPER CATALYZED COUPLING REACTION OF ARYL HALOGENO SUBSTITUTE
-
Provided are a heterocyclic carboxylic acid amide ligand and applications thereof in a copper catalyzed coupling reaction. Specifically, provided are uses of a compound represented by formula (I), definitions of radical groups being described in the specifications. The compound represented by formula (I) can be used as the ligand in the copper catalyzed coupling reaction of the aryl halogeno substitute, and is used or catalyzing the coupling reaction for forming the aryl halogeno substitute having C—N, C—O, C—S and other bonds.
- -
-
Paragraph 0266-0267
(2019/05/15)
-
- Enhancement of Benzothiazoles as Pteridine Reductase-1 Inhibitors for the Treatment of Trypanosomatidic Infections
-
2-Amino-benzo[d]thiazole was identified as a new scaffold for the development of improved pteridine reductase-1 (PTR1) inhibitors and anti-trypanosomatidic agents. Molecular docking and crystallography guided the design and synthesis of 42 new benzothiazoles. The compounds were assessed for Trypanosoma brucei and Leishmania major PTR1 inhibition and in vitro activity against T. brucei and amastigote Leishmania infantum. We identified several 2-amino-benzo[d]thiazoles with improved enzymatic activity (TbPTR1 IC50 = 0.35 μM; LmPTR1 IC50 = 1.9 μM) and low μM antiparasitic activity against T. brucei. The ten most active compounds against TbPTR1 were able to potentiate the antiparasitic activity of methotrexate when evaluated in combination against T. brucei, with a potentiating index between 1.2 and 2.7. The compound library was profiled for early ADME toxicity, and 2-amino-N-benzylbenzo[d]thiazole-6-carboxamide (4c) was finally identified as a novel potent, safe, and selective anti-trypanocydal agent (EC50 = 7.0 μM). Formulation of 4c with hydroxypropyl-β-cyclodextrin yielded good oral bioavailability, encouraging progression to in vivo studies.
- Linciano, Pasquale,Pozzi, Cecilia,Iacono, Lucia Dello,Di Pisa, Flavio,Landi, Giacomo,Bonucci, Alessio,Gul, Sheraz,Kuzikov, Maria,Ellinger, Bernhard,Witt, Gesa,Santarem, Nuno,Baptista, Catarina,Franco, Caio,Moraes, Carolina B.,Müller, Wolfgang,Wittig, Ulrike,Luciani, Rosaria,Sesenna, Antony,Quotadamo, Antonio,Ferrari, Stefania,P?hner, Ina,Cordeiro-Da-Silva, Anabela,Mangani, Stefano,Costantino, Luca,Costi, Maria Paola
-
p. 3989 - 4012
(2019/05/06)
-
- From alkylarenes to anilines via site-directed carbon–carbon amination
-
Anilines are fundamental motifs in various chemical contexts, and are widely used in the industrial production of fine chemicals, polymers, agrochemicals and pharmaceuticals. A recent development for the synthesis of anilines uses the primary amination of C–H bonds in electron-rich arenes. However, there are limitations to this strategy: the amination of electron-deficient arenes remains a challenging task and the amination of electron-rich arenes has a limited control over regioselectivity—the formation of meta-aminated products is especially difficult. Here we report a site-directed C–C bond primary amination of simple and readily available alkylarenes or benzyl alcohols for the direct and efficient preparation of anilines. This chemistry involves a novel C–C bond transformation and offers a versatile protocol for the synthesis of substituted anilines. The use of O2 as an environmentally benign oxidant is demonstrated, and studies on model compounds suggest that this method may also be used for the depolymerization of lignin.
- Liu, Jianzhong,Qiu, Xu,Huang, Xiaoqiang,Luo, Xiao,Zhang, Cheng,Wei, Jialiang,Pan, Jun,Liang, Yujie,Zhu, Yuchao,Qin, Qixue,Song, Song,Jiao, Ning
-
-
- Aromatic amine compound synthesis method
-
The invention discloses an aromatic amine compound synthesis method which is characterized in that the method is implemented according to any of two methods. The first method includes the steps: mixing an alkyl aromatic compound with a general formula (I) and a nitrogen-containing compound with a general formula (II); performing reaction on mixture under an oxidizing agent and an organic solvent to obtain an aromatic amine compound with a general formula (III). The second method includes the steps: mixing an aromatic alcohol derivative with a general formula (I') and the nitrogen-containing compound with the general formula (II); performing reaction on mixture under an acid additive and an organic solvent to prepare the aromatic amine compound with the general formula (III). According to the method, a lot of alkyl aromatic compounds or aromatic alcohol derivatives firstly serve as raw materials, and the raw materials are reacted to generate the aromatic amine compound without the action of metal catalysis. Compared with a traditional synthesis method, the synthesis method has the advantages that the method is high in yield and simple in condition, waste discharging amount is less,metal participation is omitted, a reaction device is simple, industrial production is easily achieved and the like. The method has a wide application prospect.
- -
-
Paragraph 0125-0127
(2019/01/23)
-
- AMINATION AND HYDROXYLATION OF ARYLMETAL COMPOUNDS
-
In one aspect, the present disclosure provides methods of preparing a primary or secondary amine and hydroxylated aromatic compounds. In some embodiments, the aromatic compound may be unsubstituted, substituted, or contain one or more heteroatoms within the rings of the aromatic compound. The methods described herein may be carried out without the need for transition metal catalysts or harsh reaction conditions.
- -
-
Paragraph 0098; 0134; 0135; 0204
(2018/03/25)
-
- Simple Nickel Salts for the Amination of (Hetero)aryl Bromides and Iodides with Lithium Bis(trimethylsilyl)amide
-
Recent developments in the chemistry of C-N bond formation and the synthesis of anilines have allowed for the use of first-row transition metals to catalyze these transformations. Much of the progress in this area has been driven by comprehensive screening for privileged/tailored ligands, which can be costly and not readily available in a research laboratory setting. In this communication we report a protocol in which simple nickel salts catalyze the C-N cross-coupling reaction between (hetero)aryl bromides and iodides with lithium bis(trimethylsilyl)amide without the need for any additive ligand. This method is amenable to low nickel catalyst loadings (1%) as well as gram-scale reactions. Because of the good functional group tolerance and compatibility with heterocyclic moieties, this method is useful for academic laboratory settings where access to tailored ligands and noble-metal catalysts could be challenging.
- Martinez, Gabriel Espinosa,Nugent, Joseph W.,Fout, Alison R.
-
supporting information
p. 2941 - 2944
(2018/09/21)
-
- Synergistic effects in Fe nanoparticles doped with ppm levels of (Pd + Ni). A new catalyst for sustainable nitro group reductions
-
A remarkable synergistic effect has been uncovered between ppm levels of Pd and Ni embedded within iron nanoparticles that leads to mild and selective catalytic reductions of nitro-containing aromatics and heteroaromatics in water at room temperature. NaBH4 serves as the source of inexpensive hydride. Broad substrate scope is documented, along with several other features including: low catalyst loading, low residual metal in the products, and recycling of the catalyst and reaction medium, highlight the green nature of this new technology.
- Pang, Haobo,Gallou, Fabrice,Sohn, Hyuntae,Camacho-Bunquin, Jeffrey,Delferro, Massimiliano,Lipshutz, Bruce H.
-
supporting information
p. 130 - 135
(2018/01/12)
-
- Cobalt-based nanoparticles prepared from MOF-carbon templates as efficient hydrogenation catalysts
-
The development of efficient and selective nanostructured catalysts for industrially relevant hydrogenation reactions continues to be an actual goal of chemical research. In particular, the hydrogenation of nitriles and nitroarenes is of importance for the production of primary amines, which constitute essential feedstocks and key intermediates for advanced chemicals, life science molecules and materials. Herein, we report the preparation of graphene shell encapsulated Co3O4- and Co-nanoparticles supported on carbon by the template synthesis of cobalt-terephthalic acid MOF on carbon and subsequent pyrolysis. The resulting nanoparticles create stable and reusable catalysts for selective hydrogenation of functionalized and structurally diverse aromatic, heterocyclic and aliphatic nitriles, and as well as nitro compounds to primary amines (>65 examples). The synthetic and practical utility of this novel non-noble metal-based hydrogenation protocol is demonstrated by upscaling several reactions to multigram-scale and recycling of the catalyst.
- Murugesan, Kathiravan,Senthamarai, Thirusangumurugan,Sohail, Manzar,Alshammari, Ahmad S.,Pohl, Marga-Martina,Beller, Matthias,Jagadeesh, Rajenahally V.
-
p. 8553 - 8560
(2018/11/30)
-
- Catalytic Ester and Amide to Amine Interconversion: Nickel-Catalyzed Decarbonylative Amination of Esters and Amides by C?O and C?C Bond Activation
-
An efficient nickel-catalyzed decarbonylative amination reaction of aryl and heteroaryl esters has been achieved for the first time. The new amination protocol allows the direct interconversion of esters and amides into the corresponding amines and represents a good alternative to classical rearrangements as well as cross coupling reactions.
- Yue, Huifeng,Guo, Lin,Liao, Hsuan-Hung,Cai, Yunfei,Zhu, Chen,Rueping, Magnus
-
supporting information
p. 4282 - 4285
(2017/04/03)
-
- Rapid heteroatom transfer to arylmetals utilizing multifunctional reagent scaffolds
-
Arylmetals are highly valuable carbon nucleophiles that are readily and inexpensively prepared from aryl halides or arenes and widely used on both laboratory and industrial scales to react directly with a wide range of electrophiles. Although C-C bond formation has been a staple of organic synthesis, the direct transfer of primary amino (-NH2) and hydroxyl (-OH) groups to arylmetals in a scalable and environmentally friendly fashion remains a formidable synthetic challenge because of the absence of suitable heteroatom-transfer reagents. Here, we demonstrate the use of bench-stable N-H and N-alkyl oxaziridines derived from readily available terpenoid scaffolds as efficient multifunctional reagents for the direct primary amination and hydroxylation of structurally diverse aryl- and heteroarylmetals. This practical and scalable method provides one-step synthetic access to primary anilines and phenols at low temperature and avoids the use of transition-metal catalysts, ligands and additives, nitrogen-protecting groups, excess reagents and harsh workup conditions.
- Gao, Hongyin,Zhou, Zhe,Kwon, Doo-Hyun,Coombs, James,Jones, Steven,Behnke, Nicole Erin,Ess, Daniel H.,Kürti, László
-
p. 681 - 688
(2017/06/30)
-
- Copper-Based Intermetallic Electride Catalyst for Chemoselective Hydrogenation Reactions
-
The development of transition metal intermetallic compounds, in which active sites are incorporated in lattice frameworks, has great potential for modulating the local structure and the electronic properties of active sites, and enhancing the catalytic activity and stability. Here we report that a new copper-based intermetallic electride catalyst, LaCu0.67Si1.33, in which Cu sites activated by anionic electrons with low work function are atomically dispersed in the lattice framework and affords selective hydrogenation of nitroarenes with above 40-times higher turnover frequencies (TOFs up to 5084 h-1) than well-studied metal-loaded catalysts. Kinetic analysis utilizing isotope effect reveals that the cleavage of the H-H bond is the rate-determining step. Surprisingly, the high carrier density and low work function (LWF) properties of LaCu0.67Si1.33 enable the activation of hydrogen molecules with extreme low activation energy (Ea = 14.8 kJ·mol-1). Furthermore, preferential adsorption of nitroarenes via a nitro group is achieved by high oxygen affinity of LaCu0.67Si1.33 surface, resulting in high chemoselectivity. The present efficient catalyst can further trigger the hydrogenation of other oxygen-containing functional groups such as aldehydes and ketones with high activities. These findings demonstrate that the transition metals incorporated in the specific lattice site function as catalytically active centers and surpass the conventional metal-loaded catalysts in activity and stability.
- Ye, Tian-Nan,Lu, Yangfan,Li, Jiang,Nakao, Takuya,Yang, Hongsheng,Tada, Tomofumi,Kitano, Masaaki,Hosono, Hideo
-
p. 17089 - 17097
(2017/12/06)
-
- Chemoselective Hydrogenation of Nitroarenes Catalyzed by Molybdenum Sulphide Clusters
-
Herein, we describe an atom efficient and general protocol for the chemoselective hydrogenation of nitroarenes to anilines catalyzed by well-defined diimino and diamino cubane-type Mo3S4 clusters. The novel diimino [Mo3S4Cl3(dnbpy)3]+ ([5]+) (dnbpy=4,4′-dinonyl-2,2′-dipyridyl, L1) trinuclear complex was synthesized in high yields by simple ligand substitution reactions starting from the thiourea (tu) [Mo3S4(tu)8(H2O)]Cl4?4 H2O (3) precursor. This strategy has also been successfully adapted for the isolation of the diamino [Mo3S4Cl3(dmen)3](BF4) ([6](BF4)), (dmen=N,N′-dimethylethylenediamine) salt. Applying these catalysts, high selectivity in the hydrogenation of functionalized nitroarenes has been accomplished. Over thirty anilines bearing synthetically functional groups have been synthesized in 70 to 99 % yield. Notably, the integrity of the cluster core is preserved during catalysis. Based on kinetic studies on the hydrogenation of nitrobenzene and other potential reaction intermediates, the direct reduction to aniline is the preferential route.
- Pedrajas, Elena,Sorribes, Iván,Gushchin, Artem L.,Laricheva, Yuliya A.,Junge, Kathrin,Beller, Matthias,Llusar, Rosa
-
p. 1128 - 1134
(2017/03/27)
-
- Biomass-Derived Catalysts for Selective Hydrogenation of Nitroarenes
-
Development of catalytically active materials from biowaste represents an important aspect of sustainable chemical research. Three heterogeneous materials were synthesized from inexpensive biomass-based chitosan and abundant Co(OAc)2 using complexation followed by pyrolysis at various temperatures. These materials were applied in the catalytic hydrogenation of nitroarenes using molecular hydrogen. A variety of diversely functionalized nitroarenes including some pharmaceutically active compounds were converted into aromatic amines in high yields, with high selectivity, and with excellent functional group tolerance. This green protocol has also been implemented for the synthesis of a biologically important TRPC3 inhibitor.
- Sahoo, Basudev,Formenti, Dario,Topf, Christoph,Bachmann, Stephan,Scalone, Michelangelo,Junge, Kathrin,Beller, Matthias
-
p. 3035 - 3039
(2017/08/18)
-
- Discovery of N-(Naphthalen-1-yl)-N′-alkyl Oxalamide Ligands Enables Cu-Catalyzed Aryl Amination with High Turnovers
-
A class of N-(naphthalen-1-yl)-N′-alkyl oxalamides have been proven to be powerful ligands, making a coupling reaction of (hetero)aryl iodides with primary amines proceed at 50 °C with only 0.01 mol % of Cu2O and ligand as well as a coupling reaction of (hetero)aryl bromides with primary amines and ammonia at 80 °C with only 0.1 mol % of Cu2O and ligand. A wide range of coupling partners work well under these conditions, thereby providing an easy to operate method for preparing (hetero)aryl amines.
- Gao, Jie,Bhunia, Subhajit,Wang, Kailiang,Gan, Lu,Xia, Shanghua,Ma, Dawei
-
supporting information
p. 2809 - 2812
(2017/06/07)
-
- High yielding electrophilic amination method for arylcopper reagents
-
The facilitative effect of some P-, N-, S-, and O-donor ligands in the reaction of arylcoppers with acetone O-(mesitylenesulfonyl)oxime was examined to develop a synthesis method for functionalized primary aryl amines under mild reaction conditions. Our research showed that electrophilic amination of monoaryl coppers with ketoximes can be facilitated using appropriate ligand to supply significant increase in the yield. Also, we have seen that this ligand-facilitated method is applicable in terms of arylcopper and ketoxime type and allows synthesis of primary aryl amines in good to high yields easily at room temperature in very short reaction time.
- Da?kapan, Tahir,?i?ek, Semra
-
supporting information
p. 899 - 906
(2017/04/27)
-
- Odorless, Regioselective Synthesis of Diaryl Sulfides and α-Thioaryl Carbonyls from Sodium Arylsulfinates via a Metal- Free Radical Strategy in Water
-
Regioselective arylthiolations of aromatic amines, arenols and ketones via C–H bond functionalization have been achieved with I2and PPh3in an aqueous system, whereby arylsulfenyl radicals are in situ generated from odorless sodium arylsulfinates. The arylsulfenyl radicals can react with free anilines containing electron-withdrawing groups and complex substrates (estrone and progesterone). Further experiments and quantum chemical calculations were also performed to deduce a mechanism for the formation of arylsulfenyl radicals. (Figure presented.).
- Lin, Ya-Mei,Lu, Guo-Ping,Wang, Gui-Xiang,Yi, Wen-Bin
-
supporting information
p. 4100 - 4105
(2016/12/30)
-
- Continuous flow hydrogenation of nitroarenes, azides and alkenes using maghemite-Pd nanocomposites
-
Maghemite-supported ultra-fine Pd (1-3 nm) nanoparticles, prepared by a simple co-precipitation method, find application in the catalytic continuous flow hydrogenation of nitroarenes, azides, and alkenes wherein they play an important role in the reduction of various functional groups on the surface of maghemite with catalyst loading (~6 wt% Pd). The salient features of the protocol include expeditious formation of reduced products in high yields under near ambient conditions with recycling of the catalyst (up to 12 cycles) without any decrease in selectivity and yield.
- Rathi, Anuj K.,Gawande, Manoj B.,Ranc, Vaclav,Pechousek, Jiri,Petr, Martin,Cepe, Klara,Varma, Rajender S.,Zboril, Radek
-
p. 152 - 160
(2015/12/31)
-
- Safe and Selective Nitro Group Reductions Catalyzed by Sustainable and Recyclable Fe/ppm Pd Nanoparticles in Water at Room Temperature
-
As a result of a unique synergy between ligand-free Fe/ppm Pd nanoparticles and PEG-containing designer surfactants, a facile and selective reduction of nitro-containing aromatics and heteroaromatics can be effected in water at room temperature in the presence of NaBH4. This new nanotechnology involves low catalyst loadings, is highly chemoselective, and tolerates a wide variety of functional groups. The process, which includes recycling of the entire aqueous medium, offers a general, environmentally responsible, and notably safe approach to highly valued reductions of nitro-containing compounds.
- Feng, Jie,Handa, Sachin,Gallou, Fabrice,Lipshutz, Bruce H.
-
supporting information
p. 8979 - 8983
(2016/07/26)
-
- A simple and efficient: In situ generated ruthenium catalyst for chemoselective transfer hydrogenation of nitroarenes: Kinetic and mechanistic studies and comparison with iridium systems
-
The catalytic activities of a series of in situ generated homogeneous ruthenium systems based on commercially available [RuCl2(p-cymene)]2 and various ligands in transfer hydrogenation of nitroarenes to anilines were investigated. Combination of [RuCl2(p-cymene)]2 and tridentate phenanthroline based ligand 2-(6-methoxypyridin-2-yl)-1,10-phenanthroline (phenpy-OMe) exhibited the highest catalytic activity for this reaction using 2-propanol as hydrogen source. This protocol provides a facile route to access aromatic amines under mild conditions in excellent yields. Notably, this system chemoselectively reduced the nitro groups over an array of other reactive functionalities such as ketone, alkene, amide, nitrile, and aryl halide. Operational simplicity, high yields, mild reaction conditions and short reaction times make this an attractive methodology for accessing various functionalized anilines. A series of controlled experiments and careful mechanistic investigation with the possible intermediates suggested that transformation of nitrobenzene to aniline with ruthenium and iridium system proceeded via direct route and condensation route respectively.
- Paul, Bhaskar,Chakrabarti, Kaushik,Shee, Sujan,Maji, Milan,Mishra, Anju,Kundu, Sabuj
-
p. 100532 - 100545
(2016/11/09)
-