20653-90-1Relevant articles and documents
Synthesis, characterization and catalytic epoxidation properties of a new tellurotungstate(iv)-supported rhenium carbonyl derivative
Lu, Jingkun,Ma, Xinyi,Wang, Ping,Feng, Junwei,Ma, Pengtao,Niu, Jingyang,Wang, Jingping
, p. 628 - 634 (2019/01/08)
A monomeric tellurotungstate(iv)-supported rhenium carbonyl derivative: Na2H2[(CH3)4N]6[Te2W20O70{Re(CO)3}2]·20H2O (1) has been successfully isolated and structurally characterized by single crystal X-ray diffraction crystallography, IR and UV-Vis spectroscopy, thermogravimetric analysis, etc. In particular, complex 1 could act as a efficient and reusable heterogeneous catalyst for selective epoxidation of various alkenes including different cycloalkenes, styrene derivatives, internal and long-chain alkenes. For example, cis-cyclooctene undergoes up to 98.2% conversion and >99% selectivity at 75 °C in acetonitrile with 30% H2O2 as an oxidant. Additionally, the electrocatalytic property of 1 for NO2? reduction was also investigated.
Mechanistically Driven Development of an Iron Catalyst for Selective Syn-Dihydroxylation of Alkenes with Aqueous Hydrogen Peroxide
Borrell, Margarida,Costas, Miquel
supporting information, p. 12821 - 12829 (2017/09/25)
Product release is the rate-determining step in the arene syn-dihydroxylation reaction taking place at Rieske oxygenase enzymes and is regarded as a difficult problem to be resolved in the design of iron catalysts for olefin syn-dihydroxylation with potential utility in organic synthesis. Toward this end, in this work a novel catalyst bearing a sterically encumbered tetradentate ligand based in the tpa (tpa = tris(2-methylpyridyl)amine) scaffold, [FeII(CF3SO3)2(5-tips3tpa)], 1 has been designed. The steric demand of the ligand was envisioned as a key element to support a high catalytic activity by isolating the metal center, preventing bimolecular decomposition paths and facilitating product release. In synergistic combination with a Lewis acid that helps sequestering the product, 1 provides good to excellent yields of diol products (up to 97% isolated yield), in short reaction times under mild experimental conditions using a slight excess (1.5 equiv) of aqueous hydrogen peroxide, from the oxidation of a broad range of olefins. Predictable site selective syn-dihydroxylation of diolefins is shown. The encumbered nature of the ligand also provides a unique tool that has been used in combination with isotopic analysis to define the nature of the active species and the mechanism of activation of H2O2. Furthermore, 1 is shown to be a competent synthetic tool for preparing O-labeled diols using water as oxygen source.
Metal oxide-triazole hybrids as heterogeneous or reaction-induced self-separating catalysts
Amarante, Tatiana R.,Neves, Patrícia,Valente, Anabela A.,Paz, Filipe A. Almeida,Pillinger, Martyn,Gon?alves, Isabel S.
, p. 354 - 367 (2016/07/06)
The hybrid metal oxide-triazole materials [MoO3(trz)0.5] (1) and [W2O6(trz)] (2) (trz?=?1,2,4-triazole) have been hydrothermally synthesized and characterized by different techniques (TGA, SEM, 1H and 13C MAS NMR, FT-IR spectroscopy, and structure determination by Rietveld analysis of high resolution synchrotron powder XRD data). Materials 1 and 2 display distinct behaviors when applied as catalysts for oxidation reactions with alcohol, aldehyde, olefin and sulfide substrates, and are more effective with hydrogen peroxide as the oxidant than with tert-butylhydroperoxide. The MoVI hybrid 1 transforms into soluble active species during cis-cyclooctene epoxidation with H2O2. When consumption of H2O2 reaches completion, spontaneous reassembly of the 2-dimensional molybdenum oxide network of 1 takes place and the hybrid precipitates as a microcrystalline solid that can be easily separated and recycled. Reaction-induced self-separation behavior occurs with 1, H2O2 and other substrates such as methyl oleate and methylphenylsulfide. The WVI hybrid 2 behaves differently, preserving its structural features throughout the heterogeneous catalytic process.
Crystal Structure and Catalytic Behavior in Olefin Epoxidation of a One-Dimensional Tungsten Oxide/Bipyridine Hybrid
Amarante, Tatiana R.,Antunes, Margarida M.,Valente, Anabela A.,Paz, Filipe A. Almeida,Pillinger, Martyn,Gon?alves, Isabel S.
, p. 9690 - 9703 (2015/11/03)
The tungsten oxide/2,2′-bipyridine hybrid material [WO3(2,2′-bpy)]·nH2O (n = 1-2) (1) has been prepared in near quantitative yield by the reaction of H2WO4, 2,2′-bpy, and H2O in the mole ratio of ca. 1:2:700 at 160°C for 98 h in a rotating Teflon-lined digestion bomb. The solid-state structure of 1 was solved and refined through Rietveld analysis of high-resolution synchrotron X-ray diffraction data collected for the microcrystalline powder. The material, crystallizing in the orthorhombic space group Iba2, is composed of a one-dimensional organic-inorganic hybrid polymer, ∞1[WO3(2,2′-bpy)], topologically identical to that found in the previously reported anhydrous phases [MO3(2,2′-bpy)] (M = Mo, W). While in the latter the N,N′-chelated 2,2′-bpy ligands of adjacent corner-shared {MO4N2} octahedra are positioned on the same side of the 1D chain, in 1 the 2,2′-bpy ligands alternate above and below the chain. The catalytic behavior of compound 1 for the epoxidation of cis-cyclooctene was compared with that for several other tungsten- or molybdenum-based (pre)catalysts, including the hybrid polymer [MoO3(2,2′-bpy)]. While the latter exhibits superior performance when tert-butyl hydroperoxide (TBHP) is used as the oxidant, compound 1 is superior when aqueous hydrogen peroxide is used, allowing near-quantitative conversion of the olefin to the epoxide. With H2O2, compounds 1 and [MoO3(2,2′-bpy)] act as sources of soluble active species, namely, the oxodiperoxo complex [MO(O2)2(2,2′-bpy)], which is formed in situ. Compounds 1 and [WO(O2)2(2,2′-bpy)] (2) were further tested in the epoxidation of cyclododecene, trans-2-octene, 1-octene, (R)-limonene, and styrene. The structure of 2 was determined by single-crystal X-ray diffraction and found to be isotypical with the molybdenum analogue.
Fe(PyTACN)-catalyzed cis-dihydroxylation of olefins with hydrogen peroxide
Prat, Irene,Font, David,Company, Anna,Junge, Kathrin,Ribas, Xavi,Beller, Matthias,Costas, Miquel
supporting information, p. 947 - 956 (2013/05/08)
A family of iron complexes with general formula [Fe(II)( R,Y,XPyTACN)(CF3SO3)2], where R,Y,XPyTACN=1-[2′-(4-Y-6-X-pyridyl)methyl]-4,7-dialkyl-1,4, 7-triazacyclononane, X and Y refer to the groups at positions 4 and 6 of the pyridine, respectively, and R refers to the alkyl substitution at N-4 and N-7 of the triazacyclononane ring, are shown to be catalysts for efficient and selective alkene oxidation (epoxidation and cis-dihydroxylation) employing hydrogen peroxide as oxidant. Complex [Fe(II)(Me,Me,HPyTACN)(CF 3SO3)2] (7), was identified as the most efficient and selective cis-dihydroxylation catalyst among the family. The high activity of 7 allows the oxidation of alkenes to proceed rapidly (30 min) at room temperature and under conditions where the olefin is not used in large amounts but instead is the limiting reagent. In the presence of 3 mol% of 7, 2 equiv. of H2O2 as oxidant and 15 equiv. of water, in acetonitrile solution, alkenes are cis-dihydroxylated reaching yields that might be interesting for synthetic purposes. Competition experiments show that 7 exhibits preferential selectivity towards the oxidation of cis olefins over the trans analogues, and also affords better yields and high [syn-diol]/[epoxide] ratios when cis olefins are oxidized. For aliphatic substrates, reaction yields attained with the present system compare favourably with state of the art Fe-catalyzed cis-dihydroxylation systems, and it can be regarded as an attractive complement to the iron and manganese systems described recently and which show optimum activity against electron-deficient and aromatic olefins. Copyright
Olefin-dependent discrimination between two nonheme HO-Fev=O tautomeric species in catalytic H2O2 epoxidations
Company, Anna,Feng, Yan,Gueell, Mireia,Ribas, Xavi,Luis, Josep M.,Que Jr., Lawrence,Costas, Miquel
supporting information; experimental part, p. 3359 - 3362 (2009/12/06)
A study was conducted to demonstrate olefin-dependent discrimination of two nonheme HO-Fev=O tautomeric species in catalytic H2O 2 epoxidations. Mechanistic studies were carried out under the condition of excess of olefin to minimize over-oxidation reactions and all reactions for the study were carried out under a N2 atmosphere to prevent auto-oxidation process due to presence of O2. It was observed that the diol/epoxide (D/E) ration for these reaction was dependent on the specific olefin and ranged from 3/2 (cyclooctene) to 6/1 (1-octene). The oxidation of cyclooctene using H218O2 revealed that only 28% of the oxygen atoms in the epoxide derived from H 2O2. Mechanistic results suggested that HO-Fe v=O oxidant need to be labeled before its reaction with substrates.
Epoxidation of alkenes using alkyl hydroperoxides generated in situ by catalytic autoxidation of hydrocarbons with dioxygen
Iwahama, Takahiro,Hatta, Gou,Sakaguchi, Satoshi,Ishii, Yasutaka
, p. 163 - 164 (2007/10/03)
Olefins were smoothly epoxidized under O2 (1 atm) in the presence of a hydrocarbon such as ethylbenzene or tetralin, using N-hydroxyphthalimide (NHPI) and Mo(CO)6 as catalyst; the present reaction involves autoxidation of the hydrocarbon assisted by NHPI and epoxidation of alkenes with the resulting hydroperoxide catalyzed by Mo(CO)6; cis-alkene was epoxidized in a stereospecific manner to form the corresponding cis-epoxide in high yield.
Epoxidation of alkenes with H2O2 generated in situ from alcohols and molecular oxygen using N-hydroxyphthalimide and hexafluoroacetone as catalysts
Iwahama, Takahiro,Sakaguchi, Satoshi,Ishii, Yasutaka
, p. 693 - 705 (2007/10/03)
A new epoxidation method of olefins with hydrogen peroxide and/or α- hydroxy hydroperoxide which are generated in situ from an alcohol and molecular oxygen was developed. A variety of alkenes were smoothly epoxidized with molecular oxygen in the presence of an alcohol under the influence of hexafluoroacetone (HFA) and N-hydroxyphthalimide (NHPI) as catalysts. The reaction involves the formation of α-hydroxy hydroperoxide and/or hydrogen peroxide derived from 1-phenylethanol and dioxygen by the action of NHPI and the active oxygen transfer from these hydroperoxides to HFA, giving 2- hydroperoxyhexafluoro-2-propanol which serves as the actual epoxidizing agent.
Ruthenium Tetroxide Oxidation of Alkenes. A More Complete Picture
Albarella, Laura,Piccialli, Vincenzo,Sica, Donato,Smaldone, Dina
, p. 2442 - 2456 (2007/10/03)
The ruthenium tetroxide oxidation of some linear and cyclic alkenes, representatives of five substitution patterns, has been performed in acetone-water (5:1) solution at -70 deg C using stoichiometric ammounts of the oxidant.The main reaction products are 1,2-diols and/or α-ketols depending on the nature of the substrate little amounts of scission products, aldehydes and/or carboxylic acids, are also obtained.Generally 1,2-diols predominate over α-ketols except in the oxidation of (-)-α-pinene that afforded the α-ketol in 51percent yield while no trace of the corresponding 1,2-diol was detected.All reactions prceeded through the formation of unstable brownish precipitates, presumably the intermediate ruthenium (VI) esters, which easily decomposed during the work-up step.Results from oxidation of trans-7-tetradecene and cis and trans-11-tetradecenyl acetate indicated that the reaction was syn stereospecific.In some cases, 1,3-dioxolane products, formed by condensation of the 1,2-diol and the aldehyde materials, were also obtained among the reaction products.Their possible origin is briefly discussed.
Origin of α-Hydroxy Ketones in the Osmium Tetroxide-Catalyzed Asymmetric Dihydroxylation of Alkenes
Lohray, Braj B.,Bhushan, Vidya,Kumar, R. Krishna
, p. 1375 - 1380 (2007/10/02)
The origin and the mechanism of formation of α-hydroxy ketones in the osmium tetroxide-catalyzed asymmetric cis-dihydroxylation (ADH) of alkenes in the presence of tert-butyl hydroperoxide is described.The formation of α-hydroxy ketones has been established to proceed through either the hydration of monooxobisglycolate ester 2 followed by oxidation with tert-butyl hydroperoxide (TBHP) or by acid-catalyzed addition of TBHP on the intermediate bisglycolate ester 2.On the basis of the mechanistic insight, it has been possible to shut down the formation of α-hydroxy ketones and other side products in the ADH reaction, even when TBHP is used as an oxygen source.It is possible to prepare α-hydroxy ketones in good yields but the optical purity of ketols has been found to be very low, which not only shed significant light on the mechanism of their formation, but also delineated the improbability of syntesizing them in optically active forms by ADH reaction of alkenes.
