??
LUBRIPLATE
MATERIAL SAFETY DATA SHEET
Section 1
PRODUCT NAME OR NUMBER FORMULA
LUBRIPLATE No. 405 Cutting Oil Mineral Oil and Additives
GENERIC/CHEMICAL NAME: NSF Registration No:
Petroleum Lubricating Oil N/A
Manufacturer's Name Emergency Telephone Number
Fiske Brothers Refining Co., d/b/a LUBRIPLATE Lubricants Co. 1-800-255-3924 - CHEM-TEL (24 hour)
Address Telephone Number for Information
1500 Oakdale Ave., Toledo, Ohio 43605 - 129 Lockwood St., Newark, NJ 07105 419-691-2491 - Toledo Office

Section 2 - Hazardous Ingredients/Identity Information
Non-Hazardous Ingredients CAS# Percentage
Mineral Oil 64742-54-7 20 - 25%
Mineral Oil 64742-65-0 50 - 60%
Sulfurized Esters 83488-05-5 10 - 15%
Additive N/A - Mixture 5 - 10%
Sulphur 68515-88-8 0 - 5%

Hazardous Material Identification System (HMIS): Health - 1, Flammability - 1, Reactivity - 0
Not a Controlled Product under (WHMIS) - Canada Special Protection: See Section 9

Section 3 - Health Hazard Data
5 mg/m3 for oil mist in air. OSHA Regulation 29 CFR 1910.1000
Threshold Limit Value
Effects of Overexposure Although previous National Toxicology Program (NTP) Annual Reports have not listed chlorinated paraffins as carcinogens or
potential carcinogens, recent NTP studies have shown this product to cause tumors in laboratory animals which were force-fed this product mixed with corn
oil at high dose levels for long periods of time. However, this carcinogenic response was only produced in male mice. The lack of evidence of
carnogenicity in rats and female mice with an increase in the incidence of lymphomas in male mice only is interpreted as extreme exposure conditions which
are quite unlikely to be encountered by humans during the manufacturing or handling of chlorinated paraffins. To prevent accidental swallowing of this
product, follow good personal hygiene practices, such as washing thoroughly before eating, smoking and when finished work. Also, use normal protective
equipment, such as impervious gloves and chemical splash goggles.

Carcinogenicity: NTP? No IARC Monographs? No OSHA Regulated? No

Section 4 - Emergency and First Aid Procedures
EYE CONTACT: Flush with clear water for 15 minutes or until irritation subsides. If irritation persists, consult a physician.

SKIN CONTACT: Remove any contaminated clothing and wash with soap and warm water. If injected by high pressure under skin,
regardless of the appearance or its size, contact a physician IMMEDIATELY. Delay may cause loss of affected part of the body.

INHALATION: Vapor pressure is very low and inhalation at room temperature is not a problem. If overcome by vapor from hot product,
immediately remove from exposure and call a physician. If over-exposed to oil mist, remove from further exposure until excessive oil mist
conditions subsides.

INGESTION: If ingested, call a physician immediately. Do not induce vomiting.

Section 5 - Fire and Explosion Hazard Data

COC - 380oF
Flash Point (Method Used) Flammable Limits LEL 0.9% UEL 7.0%

Extinguishing Media Foam, Dry Chemical, Carbon Dioxide or Water Spray (Fog)

Special Fire Fighting Procedures Cool exposed containers with water. Use air-supplied breathing equipment for
enclosed or confined spaces.
Unusual Fire and Explosion Hazards Do not store or mix with strong oxidants. Empty containers retain residue.
Do not cut, drill, grind, or weld, as they may explode.
PRODUCT NAME OR NUMBER - LUBRIPLATE No. 405 Cutting Oil
Section 6 - Physical/Chemical Characteristics

>550oF
Boiling Point Specific Gravity (H 2O = 1) 0.90

Vapor Pressure (mm Hg.) <0.01 Melting Point Liquid

Vapor Density (AIR = 1) >5 Evaporation Rate <0.01
(Butyl Acetate = 1)
Solubility in Water Negligible

Appearance and Odor Dark colored oil with additive odor.

Section 7 - Reactivity Data

Stability Unstable Conditions to Avoid N/A
Stable X
Incompatibility (Materials to Avoid) Avoid contact with strong oxidants like liquid chlorine, concentrated oxygen.

Hazardous Decomposition or Byproducts May form SO2. If incomplete combustion, Carbon Monoxide.

Hazardous Polymerization May Occur Conditions to Avoid N/A
Will Not Occur X

Section 8 - Spill or Leak Procedures

Steps to be taken in case material is released or spilled
Recover liquid, wash remainder with suitable petroleum solvent or add absorbent. Keep petroleum products out of sewers and water courses.
Advise authorities if product has entered or may enter sewers and water courses.

Waste disposal method
Assure conformity with applicable disposal regulations. Dispose of absorbed material at an approved waste disposal facility or site.


Section 9 - Special Protection Information

Respiratory Protection (Specify type) Normally not needed

Ventilation Local Exhaust Used to capture fumes and vapors Special N/A
Mechanical (General) Other N/A

Protective Gloves Use oil-resistant gloves, if needed. Eye Protection If chance of eye contact, wear goggles.

Other Protective Equipment Use oil-resistant apron, if needed.

Section 10 - Special Precautions

Precautions to be taken in handling and storing
Keep containers closed when not in use. Do not handle or store near heat, sparks, flame, or strong oxidants.

Other Precautions
Avoid breathing oil mist. Remove oil-soaked clothing and launder before reuse. Cleanse skin thoroughly after contact.



The above information is furnished without warranty, expressed or implied, except that it is accurate to the best knowledge of Fiske
Brothers Refining Co., d/b/a LUBRIPLATE Lubricants Co. The data on these sheets relates only to the specific material designated
herein. Fiske Brothers Refining Co., d/b/a LUBRIPLATE Lubricants Co. assumes no legal responsibility for use or reliance upon
this data.


Date Prepared: July 26, 2007 Prepared by: James R. Kontak


le oil residues me esters, sulfurized, polymd.