3M MATERIAL SAFETY DATA SHEET Jet-melt (tm) Adhesive 3796-PG / 3796-TC / 3796-Q 11/20/2002




Material Safety Data Sheet
Copyright, 2002, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.




SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: Jet-melt (tm) Adhesive 3796-PG / 3796-TC / 3796-Q
MANUFACTURER: 3M
DIVISION: Engineered Adhesives

ADDRESS: 3M Center
St. Paul, MN 55144-1000

EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)

Issue Date: 11/20/2002
Supercedes Date: 05/18/2001

Document Group: 07-4156-1

Product Use:
Specific Use: hot melt adhesive


SECTION 2: INGREDIENTS
Ingredient C.A.S. No. % by Wt
POLYESTER RESIN 51606-34-9 40 - 50
PHENOLIC ROSIN 68083-03-4 30 - 40
STYRENE-MALEIC ANHYDRIDE COPOLYMER 26762-29-8 5 - 10
POLYSTYRENE RESIN 9003-53-6 3- 7
STYRENE-BUTADIENE POLYMER 66070-58-4 3- 7
ANTIOXIDANT 6683-19-8 0.5 - 1.5




SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW

Specific Physical Form: Waxy Solid
Odor, Color, Grade: light tan, odorless (molten state - resinous odor), solid adhesive in rods.
General Physical Form: Solid
Immediate health, physical, and environmental hazards: May cause thermal burns.


3M MATERIAL SAFETY DATA SHEET Jet-melt (tm) Adhesive 3796-PG / 3796-TC / 3796-Q 11/20/2002




3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
Vapors from heated material may cause eye irritation. Signs/symptoms may include redness, swelling, pain, tearing, and blurred or
hazy vision.

Thermal Burns: Signs/symptoms may include severe pain, redness and swelling, and tissue destruction.




Skin Contact:
Thermal Burns: Signs/symptoms may include intense pain, redness and swelling, and tissue destruction.




Inhalation:
Vapors from heated material may cause irritation of the respiratory system. Signs/symptoms may include cough, sneezing, nasal
discharge, headache, hoarseness, and nose and throat pain.




Ingestion:
Physical Blockage: Signs/symptoms may include cramping, abdominal pain, and constipation.




SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES

The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.

Eye Contact: Immediately flush eyes with large amounts of water for at least 15 minutes. DO NOT ATTEMPT TO REMOVE
MOLTEN MATERIAL. Get immediate medical attention.

Skin Contact: Immediately flush skin with large amounts of cold water for at least 15 minutes. DO NOT ATTEMPT TO REMOVE
MOLTEN MATERIAL. Cover affected area with a clean dressing. Get immediate medical attention.

Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention.

If Swallowed: Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never
give anything by mouth to an unconscious person. Get medical attention.



3M MATERIAL SAFETY DATA SHEET Jet-melt (tm) Adhesive 3796-PG / 3796-TC / 3796-Q 11/20/2002


SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES

480 oF [Test Method: Cleveland Open Cup] [Details:
Flash Point
CONDITIONS: ASTM D-92-72]




5.2 EXTINGUISHING MEDIA
Ordinary combustible material. Use fire extinguishers with class A extinguishing agents (e.g., water, foam).


5.3 PROTECTION OF FIRE FIGHTERS

Special Fire Fighting Procedures: Wear full protective clothing, including helmet, self-contained, positive pressure or pressure
demand breathing apparatus, bunker coat and pants, bands around arms, waist and legs, face mask, and protective covering for
exposed areas of the head.

Unusual Fire and Explosion Hazards: Not applicable.

Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.




SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Reclaim undamaged product.

In the event of a release of this material, the user should determine if the release qualifies as reportable according to
local, state, and federal regulations.


SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
Avoid skin contact with hot material. Keep out of the reach of children.

7.2 STORAGE
Store away from heat. Store out of direct sunlight.


SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Use in a well-ventilated area.

8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)

8.2.1 Eye/Face Protection

3M MATERIAL SAFETY DATA SHEET Jet-melt (tm) Adhesive 3796-PG / 3796-TC / 3796-Q 11/20/2002


Avoid eye contact.
The following eye protection(s) are recommended: Safety Glasses with side shields, Indirect Vented Goggles.

8.2.2 Skin Protection
Avoid skin contact with hot material. Wear appropriate gloves, such as Nomex, when handling this material to prevent thermal burns.




8.2.3 Respiratory Protection
Under normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection.


8.2.4 Prevention of Swallowing
Do not ingest.


8.3 EXPOSURE GUIDELINES
None Established




SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Waxy Solid
Specific Physical Form:
light tan, odorless (molten state - resinous odor), solid adhesive in
Odor, Color, Grade:
rods.
Solid
General Physical Form:

480 oF [Test Method: Cleveland Open Cup] [Details:
Flash Point
CONDITIONS: ASTM D-92-72]


Not Applicable
Boiling point
1 g/cm3
Density

Nil
Vapor Density

Nil
Vapor Pressure
1.0 [Ref Std: WATER=1]
Specific Gravity
Not Applicable
pH
Not Applicable
Melting point

Nil
Solubility in Water
Not Applicable
Evaporation rate
Not Applicable
Volatile Organic Compounds
0 % weight
Percent volatile
Not Applicable
VOC Less H2O & Exempt Solvents
No Data Available
Viscosity


SECTION 10: STABILITY AND REACTIVITY
Stability: Stable.

Materials and Conditions to Avoid: Heat

3M MATERIAL SAFETY DATA SHEET Jet-melt (tm) Adhesive 3796-PG / 3796-TC / 3796-Q 11/20/2002




Hazardous Polymerization: Hazardous polymerization will not occur.


Hazardous Decomposition or By-Products
Substance Condition
Carbon monoxide During Combustion
Carbon dioxide During Combustion




SECTION 11: TOXICOLOGICAL INFORMATION




Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.



SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION


Not determined.

CHEMICAL FATE INFORMATION

Not determined.

SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Reclaim if feasible. If product can't be reclaimed, dispose of waste product in a sanitary landfill.
Alternatively, incinerate the waste product in an industrial, commercial, or municipal incinerator.



Since regulations vary, consult applicable regulations or authorities before disposal.


SECTION 14:TRANSPORT INFORMATION
ID Number(s):
62-3761-7230-0, 62-3761-7232-6, 62-3761-7234-2, 62-3761-7236-7, 62-3761-9132-6, 62-3761-9330-6, 62-3761-9830-5

Not regulated per U.S. DOT, IATA or IMO.



3M MATERIAL SAFETY DATA SHEET Jet-melt (tm) Adhesive 3796-PG / 3796-TC / 3796-Q 11/20/2002


These transportation classifications are provided as a customer service. As the shipper YOU remain responsible for
complying with all applicable laws and regulations, including proper transportation classification and packaging. 3M's
transportation classifications are based on product formulation, packaging, 3M policies and 3M's understanding of applicable
current regulations. 3M does not guarantee the accuracy of this classification information. This information applies only to
transportation classification and not the packaging, labeling, or marking requirements. The original 3M package is certified
for U.S. ground shipment only. If you are shipping by air or ocean, the package may not meet applicable regulatory
requirements.


SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS

Contact 3M for more information.


311/312 Hazard Categories:
Fire Hazard - No Pressure Hazard - No Reactivity Hazard - No Immediate Hazard - Yes Delayed Hazard - No



STATE REGULATIONS

Contact 3M for more information.




CHEMICAL INVENTORIES
All applicable chemical ingredients in this material are listed on the European Inventory of Existing Chemical Substances (EINECS),
or are exempt polymers whose monomers are listed on EINECS.

The components of this product are in compliance with the chemical notification requirements of TSCA.

Contact 3M for more information.




INTERNATIONAL REGULATIONS
Contact 3M for more information.




3M MATERIAL SAFETY DATA SHEET Jet-melt (tm) Adhesive 3796-PG / 3796-TC / 3796-Q 11/20/2002


This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.



SECTION 16: OTHER INFORMATION
NFPA Hazard Classification
Health: 0 Flammability: 1 Reactivity: 0 Special Hazards: None

National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.



No revision information is available.


DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.

3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.


3M MSDSs are available at www.3M.com






1,4-Benzenedicarboxylic acid, dimethyl ester, polymer with 1,6-hexanediol and .alpha.-hydro-.omega.-hydroxypoly(oxy-1,4-butanediyl)