40036-54-2Relevant academic research and scientific papers
Iron(III)-substituted polyoxotungstates immobilized on silica nanoparticles: Novel oxidative heterogeneous catalysts
Sousa, Joana L.C.,Santos, Isabel C.M.S.,Sim?es, Mário M.Q.,Cavaleiro, José A.S.,Nogueira, Helena I.S.,Cavaleiro, Ana M.V.
, p. 459 - 463 (2011)
Silica nanoparticles supporting polyoxometalates (POMs), namely an iron(III) mono-substituted Keggin-type polyoxotungstate of formula α-[PW11FeIII(H2O)O39] 4- and a sandwich-type tungstophosphate with the formula B-α-[(PW9O34)2FeIII 4(H2O)2]6- were synthesized. The POM/SiO2 nanocomposites were obtained by alkaline hydrolysis of tetraethoxysilane using a reverse micelle and sol-gel technique. The spectroscopic studies suggest that the POMs were successfully immobilized on the silica nanoparticles. The catalytic activity of POM/SiO2 nanomaterials was tested in the epoxidation of geraniol using H 2O2 as oxygen donor. The α-[PW11Fe III(H2O)O39]4-/SiO2 nanocomposite was the most efficient catalyst with high geraniol conversion and good regioselectivity for 2,3-epoxygeraniol.
New heptacoordinate tungsten(II) complexes with α-diimine ligands in the catalytic oxidation of multifunctional olefins
Vasconcellos-Dias, Maria,Nunes, Carla D.,Félix, Vítor,Brand?o, Paula,Calhorda, Maria José
, (2021/02/26)
New tungsten(II) and molybdenum(II) heptacoordinate complexes [MX2(CO)3(LY)] (MXLy: M = W, Mo; X = Br, I; LY = C5H4NCY = N(CH2)2CH3 with Y = H (L1), Me (L2), Ph (L3)) were synthesized and characterized by spectroscopic techniques and elemental analysis. The two tungsten complexes WXL1 (X = Br, I) were also structurally characterized by single crystal X-ray diffraction. The metal coordination environment is in both a distorted capped octahedron. The complexes with L1 and L2 ligands were grafted in MCM-41, after functionalization of the ligands with a Si(OEt)3 group. The new materials were characterized by elemental analysis, N2 adsorption isotherms, 29Si MAS and 13C MAS NMR. The tungsten(II) complexes and materials were the first examples of this type reported. All complexes and materials were tested as homogeneous and heterogeneous catalysts in the oxidation of multifunctional olefins (cis-hex-3-en-1-ol, trans-hex-3-en-1-ol, geraniol, S-limonene, and 1-octene), with tert-butyl hydroperoxide (TBHP) as oxidant. The molybdenum(II) catalyst precursors are in general very active, reaching 99% conversion and 100% selectivity in the epoxidation of trans-hex-3-en-1-ol. Their performance is comparable with that of the [Mo(η3-C3H5)X(CO)2(LY)] complexes, but it increases with immobilization. On the other hand, most of the W(II) complexes display an activity similar or inferior to that of the Mo(II) analogues and it decreases after they are supported in MCM-41. DFT calculations show that tungsten complexes and iodide ligands are more easily oxidized from M(II) to M(VI) than molybdenum ones, while the energies of relevant species in the catalytic cycle are very similar for all complexes, making the theoretical rationalization of experimental catalytic data difficult.
Catalytic activity of molybdenum(II) complexes in homogeneous and heterogeneous conditions
Vasconcellos Dias, Maria,Saraiva, Marta S.,Ferreira, Paula,Calhorda, Maria José
, p. 1465 - 1478 (2015/05/13)
The new complexes [MoBr(η3-C3H5)(CO)2(L)2] (C1) and [MX2(CO)3(L)2] (M = Mo(II), X = I (C2); M = Mo(II), X = Br (C3); M = W(II), X = I (C4); M = W(II), X = Br (C5)) were synthesized by reaction of 2-amino-1,3,4-thiadiazole (L) with [MoBr(η3-C3H5)(CO)2(NCCH3)2] (1), [MoI2(CO)3(CH3CN)2](M = Mo (2); M = W (4)), or [MoBr2(CO)3(CH3CN)2](M = Mo (3); M = W (5)) in 2:1 ratio. The five complexes were immobilized in MCM-41, yielding the materials MCM-Cn (n = 1-5), and C1 was also immobilized in silica gel (Silica-C1) and in a polyhedral oligomeric silsesquioxane (Cube-C1). Complexes and materials were fully characterized by spectroscopic techniques and elemental analysis. DFT calculations showed that several C1 isomers should coexist. The as synthesized and supported complexes were tested as catalysts on the oxidation of geraniol, cis-hex-3-en-1-ol, trans-hex-3-en-1-ol, (S)-limonene, and 1-octene. The conversions and TOF significantly depend on the complex and the nature of the substrate. The general conclusions are (i) complex C1 has the highest activity; (ii) tungsten complexes C4 and C5 are more active than the molybdenum analogues; (iii) the immobilization of the catalysts improves the performance; and (iv) silica gel and the polyhedral oligomeric silsesquioxane supports modify the selectivity, leading to products different from the one obtained with MCM for specific substrates.
An immobilized imidazolyl manganese porphyrin for the oxidation of olefins
De Paula, Rodrigo,Santos, Isabel C.M.S.,Sim?es, Mário M.Q.,Neves, M. Gra?a P.M.S.,Cavaleiro, José A.S.
, p. 156 - 166 (2015/05/13)
A new catalytic system based on an immobilized imidazolyl manganese porphyrin for the oxidation of olefins is presented. Merrifield resin (MR) and functionalized silica gel (SG) were chosen as supports. The results indicate that the MR system shows high reaction rates, high efficiency with hydrogen peroxide as oxidant and good recyclability up to four times, without a dramatic loss in the catalytic efficiency. The catalytic behavior seems to be strongly influenced by the immobilization reaction conditions. The oxidation reactions performed for cis-cyclooctene, styrene, cyclohexene and geraniol give the corresponding epoxides, with very high selectivity, when the MR system is used. Some considerations concerning the high efficiency of the MR system are put forward.
A new halide-free efficient reaction-controlled phase-transfer catalyst based on silicotungstate of [(C18H37)2(CH 3)2N]3[SiO4H(WO5) 3] for olefin epoxidation, oxidation of sulfides and alcohols with hydrogen peroxide
Ma, Baochun,Zhao, Wei,Zhang, Fuming,Zhang, Yingshuai,Wu, Songyun,Ding, Yong
, p. 32054 - 32062 (2014/08/18)
A new reaction-controlled phase-transfer catalyst based on silicotungstate of [(C18H37)2(CH3) 2N]3[SiO4H(WO5)3] for oxidation of hydrocarbons is developed. The catalyst is a new heteropoly compound with silicon as heteroatom, which is different to the previously reported reaction-controlled phase transfer catalysts that were composed of quaternary ammonium heteropolyoxotungstates of [π-C5H 5N(CH2)15CH3]3[PW 4O16] and [π-C5H5N(CH 2)15CH3]3[PW4O 32] with phosphorus as heteroatom. The oxidation of various alkenes (such as linear terminal olefins, internal olefins, cyclic olefins and unactivated alkenes) to epoxides, sulfides to sulfoxides and sulfones, alcohols to carbonyl compounds, are successfully catalyzed by this recyclable and environmentally benign catalyst using H2O2 as oxidant and ethyl acetate as solvent. This catalyst is not only capable of catalyzing homogeneous oxidation of organic substrates with unique reaction-controlled phase-transfer character, but also avoids the use of toxic solvents. The catalyst could be easily recovered and reused after reaction, and the epoxidation of cyclohexene was performed twenty times without obvious loss in activity. The fresh catalyst and the used one were characterized by ICP, IR, UV-vis, 29Si MAS NMR and 183W NMR in detail. the Partner Organisations 2014.
New Mo(II) complexes in MCM-41 and silica: Synthesis and catalysis
Saraiva, Marta S.,Fernandes, Cristina I.,Nunes, Teresa G.,Nunes, Carla D.,Calhorda, Maria José
, p. 443 - 452 (2014/03/21)
The new complexes [MoI2(CO)3(L1)] (1) and [MoI2(CO)3(L2)] (2) were prepared from reaction of [MoI2(CO)3(NCMe)2] with the ligands 2-(2′-hydroxyphenyl)imidazoline (L1), and 2-(2′- hydroxyphenyl) benzimidazole (L2). These complexes were immobilized in MCM-41 and in silica gel, by grafting (3- chloropropyl)trimethylsilane on the surface of the materials and allowing it to react with [MoI2(-CO) 3(L1)] (1) or [MoI2(CO)3(L 2)] (2). All the molybdenum derivatives were characterized by NMR and FTIR spectroscopies, which showed coordination of L1 and L 2 in neutral form. The structure of the MCM materials was analyzed by powder X-ray diffraction and nitrogen adsorption isotherms. The catalytic activity of the complexes and materials was tested in several substrates (cis-cyclooctene, styrene, 1- octene, R-(+)limonene, geraniol, cis-hex-3-en-1-ol and trans-hex-2-en-1-ol), using tert-butylhydroperoxide (TBHP) as oxidant. Complexes 1 and 2 were in general the more active catalysts and 100% selective towards the epoxide of cis-cyclooctene. Complex 1 immobilized in silica (Si-Pr-1) was the best material, showing higher conversion than 1 in the oxidation of R-(+)limonene, with comparable selectivity towards the ring epoxide.
Mo(II) complexes of 8-aminoquinoline and their immobilization in MCM-41
Saraiva, Marta S.,Nunes, Carla D.,Nunes, Teresa G.,Calhorda, Maria José
, p. 172 - 182 (2013/05/21)
Two new Mo(II) complexes [MoBr(η3-C3H 5)(CO)2(8-aq)] (1) and [MoI2(CO) 3(8-aq)] (2) containing the bidentate 8-aminoquinoline ligand (8-aq) were synthesized and characterized. They were immobilized in MCM-41. A 3-iodopropyltrimethoxysilane spacer reacted both with the surface, through the silane, and through the other end, with the coordinated 8-aq of complexes 1 and 2, leading to an immobilized form of the complex (MCM-Pr-1,2). In an alternative route, 8-aq reacted with 3-iodopropyltrimethoxysilane to form a new ligand L1, which could be supported in the MCM-41 and then react with the metal precursors to afford (MCM-L1-1,2). The complexes and the materials were characterized using FTIR and NMR spectroscopies, and the structure of the materials was checked with powder X-ray diffraction and nitrogen adsorption isotherms. The first synthetic procedure was less efficient in terms of metal load inside the channels of the materials. The complexes and the new materials were tested as catalytic precursors in the epoxidation of cis-cycloctene, styrene, 1-octene, R-(+)limonene, geraniol, cis-3-hexene-1-ol and trans-2-hexene-1-ol, using tert-butylhydroperoxide (TBHP) as oxidant. Although almost all the catalysts were 100% selective toward the epoxide, the conversions were in general poor. The best catalyst was complex 1, but the conversions dropped after immobilization. Conversions could be a bit improved by a careful choice of reaction conditions, the most effective being the absence of added solvent (the substrate acted as solvent).
Catalytic performance of a boron peroxotungstate complex under homogeneous and heterogeneous conditions
Santos, Isabel C.M.S.,Balula, Salete S.,Sim?es, Mário M.Q.,Cunha-Silva, Luís,Neves, M. Gra?a P.M.S.,De Castro, Baltazar,Cavaleiro, Ana M.V.,Cavaleiro, José A.S.
, p. 87 - 94 (2013/08/24)
The preparation and characterization (FT-IR, FT-Raman, 11B MAS NMR, diffuse reflectance, elemental analysis) of a novel boron peroxotungstate (BTBA)4H[BW4O24] (BTBA = benzyltributylammonium) is reported, along with its use in the homogeneous oxidation of cis-cyclooctene, geraniol, linalool and (-)-carveol with H 2O2 as oxidant and acetonitrile as solvent. High catalytic activity was registered for all the substrates studied under homogeneous conditions, namely 99% of conversion of geraniol after 2 h, 93% for linalool after 5 h, 74% for cis-cyclooctene after 6 h, and 100% for (-)-carveol after 2 h of reaction. Some oxidation studies were carried out with the Venturello complex, [PW4O24]3-, in the same conditions. Furthermore, the boron peroxotungstate (BW4) was immobilized using two different strategies: (a) BW4 anchored into a functionalized silica (aptesSiO2) giving BW4@aptesSiO2 and (b) BW4 encapsulated on a metal organic framework, commonly referred as MIL-101, giving BW4@MIL-101. The catalytic activity of both heterogeneous materials was investigated for geraniol oxidation and the results were compared with those obtained with BW4 under homogeneous conditions. The encapsulated boron peroxotungstate (BW4@MIL-101) gave rise to the best results, reaching complete conversion of geraniol after 3 h of reaction and 78% selectivity for 2,3-epoxygeraniol. Additionally, this heterogeneous catalyst could be reused without appreciable loss of catalytic activity, affording similar 2,3-epoxygeraniol selectivity. The heterogeneous catalysts' stability was also investigated after the oxidation reactions by different characterization techniques.
Vanadyl arsenates as catalysts for selective oxidation of organic sulfides and alkenes
Berrocal, Teresa,Larrea, Edurne S.,Iglesias, Marta,Arriortua, Maria I.
scheme or table, p. 176 - 182 (2011/03/23)
Two vanadyl arsenates templated with ethylendiamonium (EnVAs) and piperazonium (PipVAs) were evaluated as catalysts for the oxidation of thioethers and alkenes, using H2O2 and t-butyl hydroperoxide (TBHP) as oxidants. The intrinsic activity of EnVAs was higher than that of PipVAs for the oxidation of sulfides. Similar results were obtained when using either H2O2 or TBHP as oxidants. However, the sterical effects were enhanced when TBHP was used and higher selectivities towards sulfoxides were achieved with this oxidant. The catalytic activity of the V-based materials in the epoxidation of simple alkenes and allylic alcohols was assessed. Upon reuse, both materials show no significant decrease in their catalytic properties.
Catalytic asymmetric epoxidation
-
Page/Page column 18-19, (2010/02/12)
The present invention relates to the synthesis of chiral epoxides via a catalytic asymmetric oxidation of olefins. Additionally, the methodology provides a method of asymmetrically oxidizing sulfides and phosphines. This asymmetric oxidation employs a catalyst system composed of a metal and a chiral bishydroxamic acid ligand, which, in the presence of a stoichiometric oxidation reagent, serves to asymmetrically oxidize a variety of substrates.
