Phenothiazine-based dyes with bilateral extension of π-conjugation for efficient dye-sensitized solar cells

Article abstract of DOI:10.1016/j.dyepig.2012.11.010

Four novel organic photo-sensitizers based on phenothiazine were designed, synthesized and characterized for efficient dye-sensitized solar cells. Anisole, octyloxybenzene and dodecyloxybenzene were incorporated into the phenothiazine by an Ullmann reaction. An additional octyloxybenzene was incorporated into one dye unit through a Suzuki coupling reaction. The modified phenothiazine moiety acts as an electron donor and cyanoacrylic acid acts as an electron acceptor and anchoring unit. The photophysical, electrochemical and sensitizing characteristics of the new dyes were evaluated. The bis(octyloxybenzene) substituted dye delivered the best performance with its sensitized solar cell displaying an overall power conversion efficiency of 5.73% under standard illumination. The results indicate that bilateral conjugate extension of the π conjugation can increase their light harvesting capacity and electron lifetime, leading to improvements in the efficiency of their dye-sensitized solar cells.

Full text of DOI:10.1016/j.dyepig.2012.11.010

Dyes and Pigments 96 (2013) 722e731
Contents lists available at SciVerse ScienceDirect
Dyes and Pigments
journal homepage: www.elsevier.com/locate/dyepig
Phenothiazine-based dyes with bilateral extension of
dye-sensitized solar cells
p-conjugation for efficient
,
,
a
d
a,
*
Zafar Iqbal a c, Wu-Qiang Wu b, Dai-Bin Kuang b , Lingyun Wang , Herbert Meier , Derong Cao
**
a School of Chemistry and Chemical Engineering, State Key Laboratory of Luminescent Materials and Devices, South China University of Technology, Guangzhou 510641, China
b MOE Key Laboratory of Bioinorganic and Synthetic Chemistry, KLGHEI of Environment and Energy Chemistry, School of Chemistry and Chemical Engineering, Sun Yat-sen University,
Guangzhou 510275, China
c PCSIR Laboratories Complex, Feroze pur Road Lahore 54000, Pakistan
d Institute of Organic Chemistry, University of Mainz, Mainz 55099, Germany
a r t i c l e i n f o
a b s t r a c t
Article history:
Four novel organic photo-sensitizers based on phenothiazine were designed, synthesized and charac-
terized for efficient dye-sensitized solar cells. Anisole, octyloxybenzene and dodecyloxybenzene were
incorporated into the phenothiazine by an Ullmann reaction. An additional octyloxybenzene was
incorporated into one dye unit through a Suzuki coupling reaction. The modified phenothiazine moiety
acts as an electron donor and cyanoacrylic acid acts as an electron acceptor and anchoring unit. The
photophysical, electrochemical and sensitizing characteristics of the new dyes were evaluated. The
bis(octyloxybenzene) substituted dye delivered the best performance with its sensitized solar cell dis-
playing an overall power conversion efficiency of 5.73% under standard illumination. The results indicate
Received 2 August 2012
Received in revised form
2 November 2012
Accepted 6 November 2012
Available online 20 November 2012
Keywords:
Dye-sensitized solar cells
Phenothiazine
that bilateral conjugate extension of the
p conjugation can increase their light harvesting capacity and
electron lifetime, leading to improvements in the efficiency of their dye-sensitized solar cells.
Ó 2012 Elsevier Ltd. All rights reserved.
Bilateral extension
Recombination
Photovoltaic performance
Organic dye
1. Introduction
Metal free organic dyes being inexpensive and easy to synthe-
size with high molar extinction coefficients are advantageous over
Owing to the rapid and continuous depletion of fossil fuel
resources, there are now serious concerns over alternative sources of
energy sufficient to cater for the world’s increasing energy require-
ments [1]. Solar energy, which is enormous and essentially inex-
haustible, has the largest potential to satisfy the future global need
for renewable energy without appreciable environmental issues [2].
During the past two decades dye-sensitized solar cells (DSSCs),
a millennium technology [3] have already undergone intensive
investigation as a promising inexpensive alternative to conven-
tional pen junction solar cells since O’Regan and Grätzel reported
effective DSSCs in 1991 [4]. A significant and sustained effort has
been made to make this technology commercially viable. Metals
like ruthenium and zinc based organic dyes have already achieved
efficiencies over 11% [5,6] and 12% [7] respectively, while metal free
organic dyes have also delivered efficiency over 9% [8].
metallic organic dyes which are rather expensive and hard to
purify. However, organic dyes suffer from some drawbacks such as
lower conversion efficiencies and stability as compared to metallic
organic dyes [9e11]. One reason for the lower efficiency of the
organic dyes is related to the fast recombination which is due to
strong interaction between the organic dye and iodine. When dyes
are adsorbed on the external surface of spherical TiO2 nano-
particles, they facilitate the formation of a radial arrangement
with the acceptor anchoring segment pointing toward the TiO2
surface and the donor away from the surface. So, a rod like
configuration of the dyes attached to TiO2 pertains to which has
interspaces that provide the path for redox couples [12]. Moreover,
these rod shaped structures are susceptible to aggregation due
to strong dipoleedipole interactions between the delocalized
p-bonds, which creates hindrance in electron injection from the
excited state of the dye to the conduction band of TiO2. Further-
more, lack of an electron donating moiety in the oxidized dye plays
a vital role in recombination. Light harvesting capability of the dyes
is another major factor for the conversion efficiency from solar light
to electricity.
* Corresponding author. Tel./fax: þ86 20 87110245.
** Corresponding author. Tel.: þ86 20 84113015.
E-mail addresses: kuangdb@mail.sysu.edu.cn (D.-B. Kuang), drcao@scut.edu.cn
(D. Cao).
0143-7208/$ e see front matter Ó 2012 Elsevier Ltd. All rights reserved.
http://dx.doi.org/10.1016/j.dyepig.2012.11.010

Z. Iqbal et al. / Dyes and Pigments 96 (2013) 722e731
723
It is believed that efficient electron injection from the dye to the
conduction band of TiO2, reduction of recombination and dark
current as well as effective regeneration of dye are the leading
factors for the enhancement of power conversion efficiency [13e
15]. The effectiveness of dyes can be increased by reduction of
better than triphenylamine, tetrahydroquinoline, carbazole and
iminodibenzyles [36,37]. The additional electron rich sulfur atom
renders PTZ a stronger donor than other amines. PTZ based dyes
containing various
p spacers have been thoroughly investigated
[34,38,39]. Phenothiazine linked with other electron donating
groups like triphenylamine were studied by Tian et al., but the
efficiency remains low [35]. The dye with two PTZ units directly
linked with the conjugated system was found to be less effective as
compared to a single PTZ unit [40]. However, the dye with two PTZ
units linked with an alkyl chain has greatly enhanced the efficiency
[41,42]. Therefore, PTZ has great attraction due to its unique
structure and it can be modified for efficient DSSCs.
In the current study, systematic modifications of PTZ were made
for the enhancement of the light harvesting capabilities and
reduction of aggregation, leading to increase in efficiency of DSSCs.
Thus, a series of dyes Z1eZ4 with lateral and bilateral conjugate
extension of PTZ by incorporation of alkoxyphenyl moieties at the 7
and 10 positions were designed and synthesized (Scheme 1). Their
photophysical, photochemical and photovoltaic characteristics
were investigated in detail.
pep stacking on the TiO2 surface which always shortens the life-
time of excited states [16,17]. It has been reported that alkoxy
groups besides electron donating also reduce aggregation of dyes in
TiO2 films [18]. Aromatic rings do not only increase the light
harvesting capabilities but also reduce surface aggregation, leading
to enhancement of the electron injection rates [19]. Recently, the
effect of various alkoxy chains on triphenylamine (TPA) has been
studied and high incident photon to electric current conversion
efficiency and stability have been observed [20,21]. Various other
studies conclude that alkyl chains linked to a donor increase Voc
and suppress recombination processes [22,23]. Great progress has
been made in this field and various electron donors like TPA [24],
indoline [25], carbazole [26], merocyanine [27], polyene [28],
hemicyanine [29], fluorene [30], tetrahydroquinoline [31], phe-
noxazine [32] and phenothiazine [33] have been investigated.
Phenothiazine (PTZ) is a non-planar heterocyclic compound
which has electron rich sulfur and nitrogen atoms with a butterfly
conformation at the ground state [34]. PTZ has been widely
employed in thin film transistors, photovoltaic cells and light
emitting diodes due to its impedance in molecular aggregation and
potential hole transport characteristics [35]. Thermally and elec-
trochemically stable phenothiazine is a strong electron donor, even
2. Experimental section
2.1. Instrumentation and materials
1H NMR spectra were conducted on Bruker 400 MHz spec-
trometer in CDCl3 or DMSO-d6 with tetramethylsilane as internal
Scheme 1. Syntheses of the dyes Z1eZ4. (i) Dichlorobenzene, Cu-powder, 18-crown-6-ether, K2CO3, 185 ꢀC, 48 h; (ii) DMF, POCl3, 0 ꢀC; then dichloroethane, 1b, 90 ꢀC, overnight;
(iii) cyanoacetic acid, piperidine, acetonitrile, reflux, 5 h; (iv) chloroform, NBS, 70 ꢀC, 8 h; (v) hydroxyphenylboronic acid, THF, K2CO3, Pd(PPh3)4, 70 ꢀC, 48 h; (vi) DMF, K2CO3,
bromooctane, 130 ꢀC, 24 h.

724
Z. Iqbal et al. / Dyes and Pigments 96 (2013) 722e731
standard. MS data were recorded on an Esquire HCT PLUS mass
spectrometer. Elementary analyses were performed by using
Vario ELIII Analyzer while melting points were taken on Tek-
tronix X4 microscopic MP apparatus. Infrared spectra (FT-IR)
were recorded on KBr pellets with Bruker Tensor 27 spectrom-
eter. The absorption and emission spectra of the dyes were
conducted in THF and CH2Cl2 solutions (1 ꢁ 10ꢂ4 M) and
measured at room temperature by Shimadzu UV-2450 UVeVis
spectrophotometer and Fluorolog III photoluminescence spec-
trometer, respectively.
2.2.2. 10-(4-Octyloxyphenyl)-10H-phenothiazine (2b)
Prepared by following the synthetic procedure of 1a. 1-Iodo-4-
octyloxybenzene was reacted with phenothiazine instead of
iodoanisole to give a colorless crystalline product 2b in 54% yield,
mp 63e64 ꢀC 1H NMR (CDCl3, 400 MHz, ppm):
d 7.42e7.36 (m, 2H),
7.24e7.18 (m, 2H), 7.14e7.09(m, 2H), 6.95e6.87 (m, 4H), 6.38e6.32
(m, 2H), 4.16e4.10 (t, J ¼ 6.4 Hz, 2H), 2.02e1.94 (m, 2H), 1.70e1.62
(m, 2H), 1.57e1.45 (m, 8 H), 1.12e1.06 (t, J ¼ 6.8 Hz, 3H). FT-IR (KBr
pellet, cmꢂ1): 3061, 3005, 2949, 2848, 1605, 1570, 1510, 1295, 1248.
Electrochemical redox potentials were measured by Cyclic
Voltammetry (CV), using three electrode cells and an Ingsens 1030
electrochemical workstation (Ingsens Instrument Guangzhou, Co.
Ltd., China) in a one compartment at a scan rate of 50 mV/s. The
Ag/AgCl in KCl (3 M) solution and an auxiliary platinum wire were
utilized as reference and counter electrodes while dye coated TiO2
films were used as working electrode. Tetrabutylammonium
perchlorate (n-Bu4NClO4) 0.1 M was used as supporting electrolyte
in acetonitrile. All electrochemical measurements were calibrated
by using ferrocene as standard (0.63 V vs NHE). The currente
voltage characteristics were recorded by using a Keithley 2400
source meter under simulated AM 1.5G (100 mW cm2) illumination
with a solar light simulator (Oriel, Model: 91192). A 1000 W Xenon
arc lamp (Oriel, Model: 6271) served as a light source and its
incident light intensity was calibrated with an NREL standard Si
solar cell. The incident monochromatic photon-to-current conver-
sion efficiency (IPCE) spectra were measured as a function of
wavelength from 350 to 800 nm on the basis of a Spectral Products
DK240 monochromator. The electrochemical impedance spectra
(EIS) measurements were conducted on the electrochemical
workstation (Zahner Zennium) in dark condition, with an applied
bias potential of ꢂ0.78 V. A 10 mV AC sinusoidal signal was
employed over the constant bias with the frequency ranging
between 1 MHz and 10 mHz. The impedance parameters were
determined by fitting of the impedance spectra using Z-view soft-
ware. The amount of dye load was measured by desorbing the dye
from the films with 0.1 M NaOH in ethanol/H2O (1:1) and
measuring UVeVis spectrum [43].
2.2.3. 10-(4-Dodecyloxyphenyl)-10H-phenothiazine (2c)
Prepared by following the synthetic method of 1a. 1-Iodo-4-
dodecyloxybenzene was reacted with phenothiazine instead of
iodoanisole to give colorless crystals 2c in 53% yield, mp 57e59 ꢀC
1H NMR (CDCl3, 400 MHz, ppm):
d 7.41e7.36 (m, 2H), 7.23e7.18 (m,
2H), 7.12e7.08 (m, 2H) 6.95e6.86 (m, 4H), 6.36e6.31 (m, 2H), 4.16e
4.10 (t, J ¼ 6.4 Hz, 2H), 2.01e1.93 (m, 2H), 1.69e1.62 (m, 2H), 1.54e
1.45 (m, 16H), 1.09e1.04 (t, J ¼ 6.0 Hz, 3H). FT-IR (KBr pellet, cmꢂ1):
3062, 3005, 2920, 2851, 1605, 1570, 1510, 1297, 1236.
2.2.4. 10-(4-Methoxyphenyl)-10H-phenothiazine-3-carbaldehyde
(3a)
POCl3 (3.84 g, 25 mmol) was added drop by drop into DMF
(1.83 g, 25 mmol) at 0 ꢀC under nitrogenous environment with
continuous stirring. A solid glassy material formed which was
dissolved in dichloroethane (30 mL) and stirred for additional 1 h.
Then 1b (1.53 g, 5 mmol) dissolved in ClC2H4Cl (20 mL) was
injected into the flask and maintained at 90 ꢀC for overnight. After
cooling, the reaction mixture was poured into water (200 mL) and
pH was neutralized by slow addition of the dilute solution of
NaOH. The product was extracted with CH2Cl2 (200 mL). Organic
layer was separated and washed three times with water and dried
over anhydrous Na2SO4. The solvent was removed by rotary
evaporator. The concentrated mixture was subjected to column
chromatography using silica gel and petroleum ether/dichloro-
methane (PE/DCM) (1:1) as mobile phase. Bright yellow color
cystals of 3a were obtained in 68% (1.14 g) yield, mp 163e165 ꢀC
1H NMR (CDCl3, 400 MHz, ppm):
d 9.71e9.67 (s, 1H), 7.47e7.43
1-Iodo-4-octyloxybenzene (1b) and 1-iodo-4-dodecyloxy-
benzene (1c) were synthesized from iodophenol and respective
alkyl halide reagent according to reported method [44] while
iodoanisole (1a) and other reagents including phenothiazine,
18-crown-6-ether, Pd(PPh3)4, 4-hydroxyphenylboronic acid etc.
and solvents like o-dichlorobenzene, petroleum ether (60e90 ꢀC,
PE), dichloromethane (DCM) were purchased as reagent grade
and used without purification. All reactions were performed
under nitrogen or argon and monitored by TLC (Merck 60 F254)
and purified by column chromatography on silica gel (200e300
mesh).
(m, 1H), 7.31e7.27 (m, 3H), 7.18e7.13 (m, 2H), 6.98e6.94 (m, 1H),
6.86e6.82 (m, 2H), 6.23e6.16 (m, 2H), 3.94e3.91 (s, 3H). FT-IR
(KBr pellet, cmꢂ1): 3068, 3004, 2926, 2835, 1684, 1595, 1574,
1510, 1285, 1247.
2.2.5. 10-(4-Octyloxyphenyl)-10H-phenothiazine-3-carbaldehyde
(3b)
Prepared by the synthetic procedure of 3a. 2b was used instead
of 2a to give yellow crystals in 71.2% yield, mp 113e115 ꢀC 1H NMR
(CDCl3, 400 MHz, ppm):
d 9.72e9.68 (s, 1H), 7.48e7.44 (m, 1H),
7.30e7.25 (m, 3H), 7.16e7.12 (m, 2H), 6.99e6.94 (m, 1H), 6.87e6.82
(m, 2H), 6.24e6.17 (m, 2H), 4.08e4.03 (t, J ¼ 6.4 Hz, 2H), 1.91e1.83
(m, 2H), 1.57e1.50 (m, 2H), 1.43e1.31 (m, 8H), 0.96e0.91 (t,
J ¼ 6.4 Hz, 3H). FT-IR (KBr pellet, cmꢂ1): 3061, 3001, 2919, 2849,
1681, 1593, 1571, 1505, 1284, 1244.
2.2. Synthesis of dyes
2.2.1. 10-(4-Methoxyphenyl)-10H-phenothiazine (2a)
A mixture of iodoanisole (2.34 g, 10 mmol), phenothiazine
(5.98 g, 30 mmol), potassium carbonate (12.43 g, 90 mmol) and
electrolytic-copper powder (2.86 g, 45 mmol) in o-dichloroben-
zene (40 mL) was stirred at 185 ꢀC for 48 h. Inorganic salts were
filtered while hot. The solvent was removed under reduced pres-
sure. Purification of the crude product was carried out by column
chromatography using silica gel and petroleum ether as mobile
phase to yield 2a (5.22 g, 57%) as colorless crystals, mp 174e176 ꢀC
2.2.6. 10-(4-Dodecyloxyphenyl)-10H-phenothiazine-3-
carbaldehyde (3c)
Prepared by the synthetic method of 3a. 2c was used instead of
2a to give 3c as yellow crystals in 69.3% yield, mp 123e125 ꢀC 1H
NMR (CDCl3, 400 MHz, ppm):
d 9.72e9.68 (s, 1H), 7.46e7.42 (m,
1H), 7.31e7.28 (m, 1H), 7.27e7.22 (m, 2H), 7.16e7.11 (m, 2H), 7.09e
7.05 (m, 1H), 6.94e6.89 (m, 1H), 6.24e6.19 (m, 1H), 6.05e6.00 (m,
1H), 4.08e4.03 (t, J ¼ 6.4 Hz, 2H), 1.90e1.83 (m, 2H), 1.55e1.49 (m,
2H), 1.39e1.29 (m, 16H), 0.93e0.88 (t, J ¼ 6.4 Hz, 3H). FT-IR (KBr
pellet, cmꢂ1): 3059, 3001, 2922, 2851, 1682, 1594, 1571, 1510, 1288,
1250.
1H NMR (CDCl3, 400 MHz, ppm):
d 7.37e7.33 (m, 2H), 7.17e7.13 (m,
2H), 7.06e7.02 (m, 2H), 6.91e6.81 (m, 4H), 3.95e3.92 (s, 3H). FT-IR
(KBr pellet, cmꢂ1): 3061, 3005, 2947, 2827, 1605, 1567, 1510, 1299,
1248.

Z. Iqbal et al. / Dyes and Pigments 96 (2013) 722e731
725
2.2.7. 7-Bromo-10-(4-octyloxyphenyl)-10H-phenothiazine-3-
carbaldehyde (4)
3062, 2925, 2854, 1678, 1607, 1580, 1505, 1296, 1245. APCI-MS: m/z
635.34. Found 636.5 [M þ H]ꢂ. Anal. Calcd. for C41H49NO3S:
C, 77.44; H, 7.77; N, 2.20; S, 5.04. Found: C, 78.12; H, 7.67; N, 2.17;
S, 4.95.
10-(4-Octyloxyphenyl)-10H-phenothiazine-3-carbaldehyde 3b
(0.86 g, 2.0 mmol) was dissolved in CHCl3 (20 mL) and maintained
at 0 ꢀC. Then N-bromosuccinimide (NBS) (0.44 g, 2.5 mmol) dis-
solved in chloroform (5 mL) was injected slowly under nitrogen.
The temperature was raised to 70 ꢀC and reaction was monitored by
TLC. After 8 h the reaction mixture was cooled down to room
temperature and poured into the water. The product was extracted
with CH2Cl2 (150 mL) and organic layer was washed three times
with brine solution. The organic layer was dried over anhydrous
Na2SO4 and solvent was evaporated on rotary evaporator. Purifi-
cation of the desired product was carried out by column chroma-
tography using silica gel and PE/DCM (1:1) as mobile phase to give
required product 4 as dark yellow solid (0.767 g) in 76.7% yield, mp
2.2.10. 2-Cyano-3-(10-(4-methoxyphenyl)-10H-phenothiazin-3-yl)
acrylic acid (Z1)
A mixture of 3a (0.25 g, 0.75 mmol), dissolved in acetonitrile
(30 mL), was reacted with cyanoacrylic acid (0.64 g, 7.5 mmol) in
the presence of piperidine (0.3 mL, 3 mmol) was refluxed for 5 h
under nitrogen. After cooling the mixture was poured into 2 M
aqueous solution of HCl. It was stirred for 15 min and CH2Cl2
(200 mL) was added. The organic layer was separated and washed
again two times with water. Then organic layer was dried over
anhydrous Na2SO4. The solvent was removed under reduced pres-
sure and the crude product was subjected to column chromatog-
raphy using silica gel. First it was eluted with DCM and then by
DCM/CH3OH (20:1) to yield Z1 (0.189 g, 63.1%) as reddish black
109e111 ꢀC 1H NMR (CDCl3, 400 MHz, ppm):
d 9.71e9.87 (s, 1H),
7.45e7.41 (m, 1H), 7.31e7.28 (m, 1H), 7.26e7.21 (m, 2H), 7.16e7.11
(m, 2H), 7.09e7,04 (m, 2H), 6.93e6.88 (m, 1H), 6,23e6.19 (m, 1H),
6.04e5.98 (d, 1H), 4.08e4.02 (t, J ¼ 6.4 Hz, 2H), 1.90e1.83 (m, 2H),
1.56e1.49 (m, 2H), 1.41e1.30 (m, 8H), 0.96e0.88 (t, J ¼ 6.4 Hz, 3H).
FT-IR (KBr pellet, cmꢂ1): 3069, 3008, 2924, 2853, 1682, 1594, 1571,
1509, 1285, 1249.
solid, mp 193e195 ꢀC. 1H NMR (DMSO-d6, 400 MHz, ppm):
d 7.79e
7.70 (s, 1H), 7.63e7.55 (s, 1H), 7.28e7.18 (m, 2H), 7.09e7.00 (m, 1H),
6.97e6.81 (m, 2H), 6.20e6.20 (m, 2H), 3.92e3.80 (s, 3H). FT-IR (KBr
pellet, cmꢂ1): 3445, 3067, 2925, 2853, 2215, 1620, 1589, 1510, 1284,
1248. APCI-MS: m/z 400.09. Found 399.5 [MeH]ꢂ. Anal. calcd. for
C23H16N2O3S: C, 68.98; H, 4.03; N, 7.00; S, 8.01. Found: C, 68.89; H,
4.13; N, 6.95; S, 7.93.
2.2.8. 7-(4-Hydroxyphenyl)-10-(4-(octyloxy)phenyl)-10H-
phenothiazine-3-carbaldehyde (5)
A mixture of compound 4 (0.51 g, 1 mmol), THF (35 mL),
aqueous solution of K2CO3 (2 M, 6 mL) and Pd(PPh3)4 (10 mol%) was
heated to 45 ꢀC for half an hour under argon. Then 4-
hydroxyphenylboronic acid (0.17 g, 1.2 mmol) dissolved in THF
(5 mL) was injected slowly into the reaction mixture. The reaction
mixture was heated to 70 ꢀC and maintained for 48 h. After cooling,
it was dropped into water (500 mL) and extracted with CH2Cl2
(150 mL). The organic layer was washed three times with water
(200 mL each), then dried over anhydrous Na2SO4. The solvent was
evaporated under reduced pressure and purification was carried
out by column chromatography using silica gel and DCM as mobile
phase to give 5 as orange color solid (0.21 g) in 41% yield, mp 132e
2.2.11. 2-Cyano-3-(10-(4-(octyloxy)phenyl)-10H-phenothiazin-3-
yl)acrylic acid (Z2)
Prepared by the synthetic procedure of Z1. 3b was used instead
to 3a to give Z2 as dark black solid in 71.1% yield, mp 225e227 ꢀC 1H
NMR (DMSO-d6, 400 MHz, ppm):
d 7.90e7.82 (s, 1H), 7.67e7.63 (s,
1H), 7.47e7.42 (m, 1H), 7.34e7.30 (m, 2H), 7.22e7.17 (m, 2H), 7.06e
7.02 (m, 1H), 6.93e6.85 (m, 2H), 6.15e6.09 (t, 2H), 4.08e4.00 (t,
J ¼ 6.4 Hz, 2H), 1.78e1.72 (m, 2H), 1.47e1.41 (m, 2H), 1.32e1.24 (m,
8H), 0.88e0.84 (t, J ¼ 6.8 Hz, 3H). FT-IR (KBr pellet, cmꢂ1): 3444,
3061, 2926, 2854, 2216, 1618, 1589, 1510, 1291, 1247. APCI-MS: m/z,
498.20, Found: 497.1 [MeH]ꢂ. Anal. calcd. for C30H30N2O3S :
C, 72.26; H, 6.06; N, 5.62; S, 6.43. Found: C, 72.68; H, 5.90; N, 5.52;
S, 6.44.
134 ꢀC 1H NMR (CDCl3, 400 MHz, ppm):
d 9.70e9.63 (s, 1H), 7.49e
7.41 (m, 1H), 7.35e7.30 (m, 2H), 7.27e7.24 (m, 2H), 7.15e7.10 (m,
2H) 7.00e6.94 (m,1H), 6.89e6.81 (m, 2H), 6.24e6.13 (m, 2H), 5.76e
5.55 (s, 1H), 4.09e3.98 (t, J ¼ 6.4 Hz, 2H), 1.89e1.80 (m, 2H), 1.55e
1.46 (m, 2H), 1.39e1.25 (m, 8H), 0.93e0.86 (t, J ¼ 6.0 Hz, 3H). FT-IR
(KBr pellet, cmꢂ1): 3400, 3055, 2926, 2854, 1667, 1580, 1568, 1507,
1289, 1248. APCI-MS: m/z 523.22 Found 522.31 [MeH]ꢂ. Anal.
calcd. for C33H33NO3S: C, 75.69; H, 6.35; N, 2.67; S, 6.12. Found: C,
76.07; H, 6.34; N, 2.60; S, 5.98.
2.2.12. 2-Cyano-3-(10-(4-(dodecyloxy)phenyl)-10H-phenothiazin-
3-yl)acrylic acid (Z3)
Prepared by the synthetic procedure of Z1. Compound 3c was
condensed with cyanoacrylic acid instead of 3a to give Z3 as black
solid in 66.7% yield, mp 213e215 ꢀC 1H NMR (DMSO-d6, 400 MHz,
ppm):
d 7.95e7.79 (s, 1H), 7.71e7.58 (s, 1H), 7.50e7.41 (m, 1H),
7.39e7.26 (m, 2H), 7.25e7.13 (m, 2H), 7.09e7.00 (m, 1H), 6.97e6.79
(m, 2H), 6.29e5.97 (m, 2H), 4.12e3.99 (t, J ¼ 6.4 Hz, 2H), 1.83e1.65
(m, 2H), 1.48e1.40 (m, 2H), 1.39e1.12 (m, 16H), 0.91e0.79 (t,
J ¼ 6.8 Hz, 3H). FT-IR (KBr pellet, cmꢂ1): 3444, 3066, 2924, 2853,
2218, 1610, 1568, 1510, 1290, 1248. APCI-MS: m/z 554.2. Found:
553.0 [MeH]ꢂ. Anal. calcd. for C34H38N2O3S: C, 73.61; H, 6.91; N,
5.05; S, 5.78. Found: C, 73.65, H, 6.82; N, 5.06; S, 5.88.
2.2.9. 7,10-Bis(4-(octyloxy)phenyl)-10H-phenothiazine-3-
carbaldehyde (6)
A mixture of 5 (0.183 g, 0.35 mmol), K2CO3 (0.073 g, 0.53 mmol)
and DMF (35 mL) was stirred for half an hour at room temperature
and then bromooctane (0.135 g, 0.7 mmol) was injected under
nitrogen. It was then heated to 130 ꢀC and maintained for 24 h.
After cooling, the reaction mixture was poured into water (500 mL)
and stirred for half an hour. Then CH2Cl2 (200 mL) was added and
water layer was separated. The organic layer was washed several
times with water, dried over anhydrous Na2SO4 and then solvent
was removed by rotary evaporator. Column chromatography was
carried out by using silica and PE/DCM (1:1) as mobile phase to
yield 6 (0.170 g, 91%) as yellow solid, mp 82e84 ꢀC 1H NMR (CDCl3,
2.2.13. 2-Cyano-3-(7,10-Bis(4-(octyloxy)phenyl)-10H-
phenothiazin-3-yl)acrylic acid (Z4)
Prepared by the synthetic procedure of Z1. Compound 6 was
condensed with cyanoacrylic acid instead of 3a to give Z4 as dark
red solid in 61.6% yield, mp 144e146 ꢀC 1H NMR (DMSO-d6,
400 MHz, ppm):
d 7.93e7.89 (s, 1H), 7.70e7.69 (m, 1H), 7.50e7.46
400 MHz, ppm):
d
9.75e9.69 (s,1H), 7.52e7.46 (d, 1H), 7.43e7.38 (d,
(m, 3H), 7.36e7.32 (m, 2H),7.31e7.29 (m, 1H), 7.22e7.19 (m, 1H),
7.17e7.14 (m, 1H), 6.96e6.92 (m, 2H), 4.07e4.03 (t, J ¼ 6.4 Hz, 2H),
3.98e3.94 (t, J ¼ 6.4 Hz, 2H), 1.78e1.73 (m, 2H), 1.72e1.67 (m, 2H),
1.46e1.38 (m, 4H), 1.32e1.24 (m, 16H), 0.89e0.84 (t, J ¼ 7.2 Hz, 6H).
FT-IR (KBr pellet, cmꢂ1): 3446, 3060, 2926, 2855, 2218, 1608, 1576,
2H), 7.32e7.27 (m. 3H), 7.20e7.13 (d, 3H), 7.06e6.99 (m, 1H), 6.97e
6.90 (d, 2H), 6.29e6.19 (m, 2H), 4.11e4.04 (t, J ¼ 6.4 Hz, 2H), 4.03e
3.96 (t, J ¼ 6.4 Hz, 2H), 1.91e1.78 (m, 4H), 1.57e1.47 (m, 4H), 1.41e
1.30 (m, 16H), 0.95e0.90 (t, J ¼ 7.2 Hz 6H). FT-IR (KBr pellet, cmꢂ1):

726
Z. Iqbal et al. / Dyes and Pigments 96 (2013) 722e731
1509, 1286, 1245. APCI-MS: m/z 702.35, Found: 701.7 [MeH]ꢂ, Anal.
Calcd. for C40H50N2O4S: C, 75.18; H, 7.17; N, 3.99; S, 4.56. Found: C,
74.76; H, 6.97; N, 3.99; S, 4.48.
DMF and POCl3. These reagents were condensed with cyanoacrylic
acid via Knoevenagel condensation reactions in the presence of
piperidine resulting in the dyes Z1, Z2 and Z3. Reagent 3b was
brominated with NBS in chloroform to give compound 4. Suzuki
coupling reaction of compound
4 was carried out with 4-
2.3. Fabrication of the dye-sensitized solar cells
hydroxyphenylboronic acid to give compound 5, which was alky-
lated in the presence of DMF and potassium carbonate to give
compound 6. Finally 6 was converted by Knoevenagel condensation
to the dye Z4. All the intermediates and target dyes were confirmed
by standard spectroscopic methods.
Fluorine-doped tin oxide (FTO) glasses were washed with
detergent, water, ethanol and acetone in an ultrasonic bath for
removing dirt and debris anatase TiO2 nano-particles (20 nm) were
prepared through a hydrothermal treatment with a precursor solu-
tion containing Ti(OBu)4 (10 mL), ethanol (20 mL), acetic acid (18 mL)
and deionized water (50 mL) according to the previously reported
paper [20,45]. The synthesized TiO2 powder (1.0 g) was ground for
40 min in the mixture of ethanol (8.0 mL), acetic acid (0.2 mL),
terpineol (3.0 g) and ethyl cellulose (0.5 g) to form homogeneous
slurry. Finally, the slurry was sonicated for 15 min in an ultrasonic
bath to form a viscous white TiO2 paste. Then the TiO2 photoanodes
3.2. Photophysical properties
UVeVis absorption and emission spectra of the dyes Z1eZ4 in
THF/DCM (1:1) solution (1 ꢁ 10ꢂ4 M) and adsorbed on a thin TiO2
film are presented in Table 1, Figs. 1 and 2. The UV spectra of the
dyes exhibit two distinct bands, one at 306e324 nm and the other
(about 18
mm in thickness) were prepared via screen-printing
at 420e459 nm. The first band corresponds to the pep* transition
process onto FTO glass. The prepared films were annealed through
a procedure (325 ꢀC for 5 min, 375 ꢀC for 5 min, 450 ꢀC for 15 min, and
500 ꢀC for 15 min) to remove the organic substances. Then TiO2 films
were soaked in 0.04 M TiCl4 aqueous solution for 30 min at 70 ꢀC to
improve the photocurrent and photovoltaic performance. Treated
films were rinsed with deionized water and ethanol and then sin-
tered again at 520 ꢀC for 30 min. After cooling to 80 ꢀC the films were
immersed in a 5.0 ꢁ 10ꢂ4 M solution of Z1eZ4 dyes for 16 h (0.5 mM
dye in a mixture of tetrahydrofuran and dichloromethane, 1:1
volume ratio). Afterward these films were rinsed with CH2Cl2 in
order to remove physical adsorbed organic dye molecules. To eval-
uate their photovoltaic performance, the dye-sensitized TiO2/FTO
glass films were assembled into a sandwiched type together with
Pt/FTO counter electrode. Platinized counter electrodes were fabri-
cated by thermal depositing H2PtCl6 solution (5 mM in isopropanol)
onto FTO glass at 400 ꢀC for 15 min. The electrolyte (0.6 M 1-methyl-
3-propylimidazolium iodide (PMII), 0.10 M guanidinium thiocyanate,
0.03 M I2 and 0.5 M tert-butylpyridine) in acetonitrile/valeronitrile
(85:15) was injected from a hole made on the counter electrode
into the space between the sandwiched cells. The active area of the
dye coated TiO2 film was 0.16 cm2.
of the localized conjugated skeleton while the other band can be
assigned to an intramolecular charge transfer (ICT) between the
central phenothiazine (electron donor) and the cyanoacetic acid
(electron acceptor and anchoring moiety). UV absorption lmax
increases by 39 nm from Z1 with methoxy group to Z2 with
octyloxy chain due to the increase in chain length which imparts
a strong electron donating capability or may effect J-type aggre-
gation. The dye Z3 with a dodecyloxy chain in comparison to Z2
was 31 nm blue shifted due to its flexible structure since the inter-
chain distances increased linearly with increasing length of alkyl
chain. Similar studies with dramatic results from increasing alkyl
chain length have been reported [46e50]. The dye Z4 gave
a maximum absorption similar to the dye Z2 but its molar
extinction coefficient (ε ¼ 34,350 Mꢂ1 cmꢂ1) was higher than the
dye Z2 (ε ¼ 20,640 Mꢂ1 cmꢂ1), which indicates that the absorp-
tion capacity of the dye Z4 was enhanced by the bilateral exten-
sion. Molar extinction coefficients of the dyes were in the order of
Z4 > Z2 > Z3 > Z1 (Table 1). Red shift and enhanced epsilon favor
the light harvesting and hence photocurrent generation in DSSCs.
Furthermore, the octyloxy chain gives a more compact and
balanced structure and better absorbance of light [51]. After being
adsorbed on the surface of TiO2 films, all dyes showed broadening
of UVevis absorption and a red shift of lmax as compared to those
in solution (Table 1), which favors the light harvesting potential of
solar cells leading to increase of Jsc. Red shifts of 30 nm, 7 nm,
37 nm and 11 nm in absorption maxima were observed in the
dyes Z1, Z2, Z3 and Z4 respectively The variations in absorption
spectra of Z1 and Z3 were more pronounced which may be
ascribed to a change in the format of aggregation on TiO2 surface
as compared to solution. Hypsochromic shifts on the TiO2 surface
were assigned to the interaction of the anchoring group
3. Results and discussion
3.1. Synthesis and structural characterization
The synthetic route of the dyes is shown in Scheme 1. Iodoani-
sole (1a) was purchased while 1-iodo-4-octyloxybenzene (1b) and
1-iodo-4-dodecyloxybenzene (1c) were prepared from iodophenol
via alkylation reaction with bromooctane and bromododecane
respectively. Compounds 2aec were prepared by the Ullmann
reaction using electrolytic copper and 18-crown-6-ether as catalyst
in o-dichlorobenzene at 185 ꢀC. The aldehydes 3aec were then
synthesized by the VilsmeiereHaack reaction in the presence of
with surface anions which directly reduces the energy of the
p*
level and the formation of J-aggregates on the TiO2 surface
[16,52,53].
Table 1
Absorption and emission characteristics of the dyes Z1eZ4.
b
Dye
Absorption
ε (Mꢂ1 cmꢂ1
)
Emission
Absorption
Red shift of absorption
lmax (nm)
Amount of dye load
lmax (nm)a
lmax (nm)c
lmax (nm)d
(Molꢂ1 cmꢂ2
)
Z1
Z2
Z3
Z4
313, 420
324,459
315, 428
306, 459
18,500, 7750
20,640, 11,920
18,820, 8260
34,350, 14,680
550
566
552
570
450
463
465
470
30
7
37
11
2.10 ꢁ 10ꢂ7
1.12 ꢁ 10ꢂ7
1.03 ꢁ 10ꢂ7
1.26 ꢁ 10ꢂ7
Absorption maximum of dyes measured in THF/DCM (1:1) with concentration 1 ꢁ 10ꢂ4 mol/L.
The molar extinction coefficient at lmax in solution.
a
b
c
Emission maximum of dyes in THF/DCM (1:1) with concentration 1 ꢁ 10ꢂ4 mol/L.
Absorption maximum of dyes adsorbed on the surface of TiO2.
d

Z. Iqbal et al. / Dyes and Pigments 96 (2013) 722e731
727
Fig. 1. (a) Normalized absorption spectra and (b) normalized emission spectra of the dyes in THF/CH2Cl2.
3.3. Electrochemical properties
previous studies [19]. All LUMO levels of dyes are reasonably suit-
able for providing sufficient thermodynamic driving force for
electron injection from the excited state to the conduction band of
TiO2 (0.5 eV vs NHE) [54]. The requirement for appropriate electron
injection from the excited state to the conduction band of titanium
dioxide is 0.2 eV [55]. The HOMO energies of all dyes are also well in
accordance, lower than Iꢂ/I3ꢂ potential (0.4 eV vs NHE) [56], sug-
gesting that there should be enough driving force for the regener-
ation of the dyes.
In order to investigate the ability of electron transfer from the
excited dye molecule to the conductive band of TiO2 the redox
behavior of dyes Z1eZ4 was studied by cyclic voltammetry (CV)
(Figs. 3 and 4, Table 2). CV was carried out in tetrabutylammonium
perchlorate (0.1 M) in acetonitrile as supporting electrolyte, Ag/
AgCl in KCl (3 M) solution as reference electrode, Platinum wire as
counter electrode and TiO2 films as working electrode. Each
measurement was calibrated with Fc/Fcþ (ferrocene/ferrocenium
ion) and converted to NHE by the addition of 0.63 eV. Onset
oxidation potentials of the dyes figured out the highest occupied
molecular orbitals (HOMO) of 1.54 eV, 1.35 eV, 1.47 eV and 1.44 eV
(Fc/Fcþ vs NHE) for Z1, Z2, Z3 and Z4 respectively. The lowest
unoccupied molecular orbitals (LUMO) were estimated by oxida-
tion potential and the energy at the intersection of absorption and
emission spectra, which are ꢂ0.97 eV, ꢂ1.09 eV, ꢂ1.03 eV
and ꢂ0.93 eV for Z1, Z2, Z3 and Z4 respectively. The band gap of Z4
was reduced considerably by the introduction of bilateral substit-
uents as compared to those of Z1eZ3 with the lateral substitution
alone. Maximum absorption and higher extinction coefficient dyes
have shorter energy gaps. These findings are quite similar to the
3.4. Molecular orbital calculations
To gain further insight into the above mentioned results density
function theory (DFT) calculations were carried out by using
Gaussian 09 software at the B3LYP/6-31G (d, p) levels [57]. Opti-
mized structures and the electronic distribution in HOMO and
LUMO levels are presented in Fig. 4, Table 2. The electron distri-
butions of the Z1eZ4 in the HOMOs levels were mainly localized on
phenothiazine moiety while the LUMOs showed localized electron
distribution through the cyanoacrylic acid upon light illumination.
Therefore, HOMOeLUMO excitation by light induced shift of the
electron from the PTZ donor moiety to the acceptor moiety. This
separation of electrons ensures the efficient electron injection from
the dye to the TiO2 film. The geometry of phenothiazine was
butterfly shaped due to the sp3 hybridization of the N and S
heteroatoms. The side chain (alkoxybenzene) attached to the 7 and
10 positions of phenothiazine increases the bulkiness of the
molecules, therefore preventing the formation of excimers and
aggregates [58].
3.5. Photovoltaic performance of the DSSCs
A set of dye-sensitized solar cells was fabricated as described in
the experimental section and tested under standard conditions
(AM 1.5G, 100 mW cmꢂ2) in order to investigate the photovoltaic
performance of the dyes. The incident monochromatic photon-to-
current conversion efficiency (IPCE) and photocurrent densitye
voltage (JeV) curves of the four dyes Z1eZ4 were obtained with
a sandwich cell comprising of 18
redox electrolyte.
m
m TiO2 photoanode and Iꢂ/I3ꢂ
The JeV curves based on dyes Z1eZ4 are shown in Fig. 5. The
detailed parameters of short-circuit photocurrent density (Jsc),
open-circuit voltage (Voc), fill factor (FF) and overall conversion
Fig. 2. Absorption spectra of the dyes adsorbed on TiO2 films.

728
Z. Iqbal et al. / Dyes and Pigments 96 (2013) 722e731
Fig. 3. Cyclic voltammetry (a) and HOMO/LUMO levels (b) of the dyes Z1eZ4.
efficiency (
based on Z4 exhibits
h
) are summarized in Table 3. Among these dyes, the cell
A similar trend was observed in Jsc, i.e. Z4 > Z2 > Z1 > Z3, corre-
a
maximum efficiency of 5.73%
sponding to 10.35, 8.65, 8.56 and 8.47 mA cmꢂ2, respectively. This
behavior of the dyes can be attributed to alkoxy chains self-
assembling into layers which are apt to extend between TiO2 film
and Iꢂ/Iꢂ3 electrolyte, thus blocking the recapture of the photo-
injected electrons by triiodide ions. In addition, lengthening of the
alkoxy chains of the dyes could result in a longer distance between
the TiO2 layer and the electrolyte. The efficiency of the dye Z3 is
lower as the alkoxy chain is soft and twisted and may be too long
for this structure, so that Z3 cannot effectively improve the
photovoltaic performance. This long chain may create hindrance for
the hole transportation leading to a more pronounced effect of
recombination. Furthermore, it also masks the TiO2 surface and
render less effective attachment of the anchoring unit. This
phenomenon was confirmed by measuring the dye load (Table 1),
which indicates that Z3 has the minimum dye load as compared to
other dyes. Z3 also has a lowest Jsc value which is associated with
the weak adsorption onto the TiO2 surface, low charge separation
and low transportation efficiency. The highest efficiency of the cell
based on Z4 is due to its relatively higher Jsc, which is ascribed to its
higher light harvesting capacity in the visible region. It was re-
ported that variations in open-circuit voltage and short-circuit
current density are related to electron lifetime in the conduction
band of TiO2 [59].
(Jsc ¼ 10.35 mA cmꢂ2, Voc ¼ 802 mV, FF ¼ 0.69) under standard
global AG 1.5G solar light illumination (100 mW cmꢂ2). Under
similar measuring conditions, other cells sensitized with the dyes
Z1, Z2 and Z3 showed Jsc of 8.56, 8.65 and 8.47 mA cmꢂ2, Voc of 773,
785 and 768 mV and FF of 0.69, 0.71 and 0.70, corresponding to
h of
4.53, 4.79 and 4.54%, respectively. As seen in the results, the Voc
increases from 773 mV to 785 mV by increasing chain length from
methoxy (Z1) to octyloxy (Z2). This was assigned to reduced
recombination ability at TiO2/dye/electrolyte interface by insu-
lating alkoxy chains on the dyes. The dye Z3 has a smaller open
circuit-voltage as compared to the dye Z2 though the chain length
increases from octyloxy to dodecyloxy, which can be ascribed to its
loose structure and less resistance in recombination as well as
hindrance in dye regeneration. The dye Z4 has maximum Voc
802 mV, which is due to its bilateral resistance by alkoxy chains.
IPCE spectra of Z1eZ4 for DSSCs are plotted in Fig. 6. The IPCE
values of DSSCs based on Z4 exceed 70% from 450 nm to 550 nm
with a maximum value of 84.39% at 470 nm and tail-off toward
670 nm. While maximum IPCE of the dyes Z1, Z2 and Z3 exceeds 71,
79 and 69% at 460, 460 and 450 nm with tail off toward 640, 630
and 640 nm, respectively. This trend of IPCE spectra
(Z4 > Z2 > Z1 > Z3) is in good accordance with the order of short-
circuit photocurrent density indicating that higher wavelength
absorption dyes have higher Jsc. It is worth noting that the IPCE
spectrum of a Z4 based cell shows an obvious shift to a longer
wavelength. The highest IPCE value of Z4 was attributed to its
broader absorption and enhanced molar extinction coefficient in
the visible region, which is in good agreement with the absorbance
spectra of the dyes in solution and on the TiO2 films. Therefore, the
higher and broader IPCE of the cell based on Z4 leads to a higher
short-circuit photocurrent density, which is conducive to improve
the photovoltaic performance of DSSCs.
To further illustrate the difference in Voc among the DSSCs
based on different dyes and investigate the interfacial charge
transfer process within DSSCs, the electrochemical impedance
spectra (EIS) was performed in the dark under a forward bias
Fig. 4. Optimized structures and frontier molecular orbitals of the HOMO and LUMO
calculated by DFT on a B3LYP/6-31 þ G (d, p) level.

Z. Iqbal et al. / Dyes and Pigments 96 (2013) 722e731
729
Table 2
Electrochemical characteristics of the dyes Z1eZ4.
Dyes
l
(nm)a
HOMO (eV) vs NHEb
E0e0 (eV) vs NHEc
LUMO (eV) vs NHEd
HOMO (eV) vs vacuume
LUMO (eV) vs vacuume
E-gap (eV)
Z1
Z2
Z3
Z4
494.4
508.2
496.8
522.2
1.54
1.35
1.46
1.44
2.51
2.44
2.50
2.37
ꢂ0.97
ꢂ1.09
ꢂ1.04
ꢂ0.93
ꢂ5.22
ꢂ5.19
ꢂ5.20
ꢂ5.09
ꢂ2.57
ꢂ2.56
ꢂ2.56
ꢂ2.50
ꢂ2.65
ꢂ2.63
ꢂ2.64
ꢂ2.59
a
l
intersection obtained from the cross point of absorption and emission spectra in THF/DCM (1:1) solution.
HOMO of dyes measured by cyclic voltametery in 0.1 M tetrabutylammonium perchlorate in acetonitrile solution as supporting electrolyte, Ag/AgCl as reference electrode
and Pt as counter electrode.
b
c
E0e0 ¼ 1240/
l intersection.
d
e
LUMO was estimated by E0e0 ꢂ HOMO.
HOMO and LUMO were calculated at B3LYP-3 G(d, p) level in vacuum.
Fig. 5. JeV curves of DSSCs sensitized by the dyes Z1eZ4.
Fig. 6. IPCE spectra of DSSCs based on the dyes Z1eZ4.
results in a larger value of Voc. The dye Z3 with a dodecyloxy chain
has least electron lifetime and resistance of recombination as
compared to the dye Z2 with an octyloxy chain. It has been
reported that an alkoxy chain can act as charge suppression
function of the charge recombination [63]. We have found that the
dodecyloxy chain was less effective than octyloxy chain, which
may be due to inefficient hole mobility which results in recom-
bination and lowers the values. Similar results were found in
regioregular poly (3-alkylthiophene)s, where charge mobility was
influenced by increasing alkyl chain from C4 to C12 [60]. The dye
Z4 performs the best in respect of all photovoltaic parameters
because the bilateral conjugation of octyloxybenzene plausibly
of ꢂ0.78 V to investigate the interfacial charge transfer process
within DSSCs. As shown in Fig. 7, two semicircles were observed in
the Nyquist plots. The smaller (higher frequency from 103 to
105 Hz) and larger semicircles (lower frequency from 1 to 102 Hz)
in the Nyquist plots were attributed to the charge transfer at the
counter electrode/electrolyte interface and the TiO2/dye/electro-
lyte interface respectively. Small circles were almost similar in all
the dyes due to the use of same counter electrode and electrolyte.
On the other hand, there is an obvious difference in the large
semicircles, which indicates that charge transfer behavior
between TiO2 and electrolyte was significantly altered, which was
likely due to the surface modifications with different dyes. As
shown in Fig. 7, the recombination resistance of the dye Z4 based
cell was larger than those of other cells according to the value
derived from curve fitting in Z-view software. Electron lifetime
calculated by fitting the equation sr ¼ Rrec ꢁ CPE2 (CPE2, chemical
capacitance) [60e62] decreased gradually in the order of
Z4 > Z2 > Z1 > Z3 (210, 184, 161 and 130 ms, respectively), these
results are in good agreement with the variation tendency of Voc
(Z4 > Z2 > Z1 > Z3) measured by the JeV curves. The longer
electron lifetime within different dye based cells leads to less
possibility of electron recombination within the DSSCs and thus
Table 3
Photovoltaic parameters of DSSCs based on Z1eZ4.
Dyes
Jsc (mA cmꢂ2
)
Voc (mV)
FF
h
(%)
Electron lifetime (sr, ms)
Z1
Z2
Z3
Z4
8.56
8.65
8.47
773
785
768
802
0.69
0.71
0.70
0.69
4.53
4.79
4.54
5.73
0.161
0.184
0.130
0.210
10.35
Fig. 7. Electrochemical impedance spectra of the dyes Z1eZ4 measured in the dark.

730
Z. Iqbal et al. / Dyes and Pigments 96 (2013) 722e731
[18] Lee DH, Lee MJ, Song HM, Song BJ, Seo KD, Pastore M, et al. Organic dyes
incorporating low band gap chromophores based on -extended benzothia-
diazole for dyes-sensitized solar cells. Dyes and Pigments 2011;91:192e8.
[19] Wu QP, Xu YJ, Cheng XB, Liang M, Sun Z, Song X. Synthesis of triarylamines
with secondary electron-donating groups for dye-sensitized solar cells. Solar
Energy 2012;86:764e70.
increases light harvesting capacity, electron lifetime and resis-
tance to recombination of electrons.
p
4. Conclusions
[20] Lei BX, Fang WJ, Hou YF, Liao JY, Kuang DB, Su CY. All solid state electrolytes
consisting of ionic liquid and carbon black for efficient dye-sensitized solar
cells. Journal of Photochemistry and Photobiology A 2010;216:8e14.
[21] Su CY, Yu QY, Liao JY, Zhou SM, Shen Y, Liu JM, et al. Effect of hydrocarbon chain
length of disubstituted triphenylamine based organic dyes on dye-sensitized
solar cells. Journal of Physical Chemistry C 2011;115:22,002e22,008.
[22] Koumura N, Wang ZS, Mori S, Miyashita M, Suzuki E, Hara K. Alkyl-func-
tionalized organic dye for efficient molecular photovoltaic. Journal of Amer-
ican Chemical Society 2006;128:14,256e14,257.
[23] Liu W, Wu IC, Lai CH, Chou PT, Li YT, Chen CL, et al. Simple organic molecule
bearing a 3,4ethylenedioxythiiophene linker for efficient dye sensitized solar
cells. Chemical Communications 2008:5152e5.
[24] Tian H, Yang X, Chen R, Zhang R, Hagfeldt A, Sun L. Effect of different dye baths
and dye structures on the performance of dye sensitized solar cells based on
triphenylamine dyes. Journal of Physical Chemistry C 2008;112:11,023e11,033.
[25] Cheng HM, Hsieh WF. Electron transfer properties of organic dye sensitized
solar cells based on indoline sensitizer with ZnO nanoparticles. Nanotech-
nology 2010;21:485,202e485,210.
Four novel dyes (Z1eZ4) based on modifications of pheno-
thiazine with different alkoxy chain lengths and increased
conjugation were designed and synthesized. The dye Z2 with
octyloxy chain was found superior to the dye Z3 with dodecyloxy
chain in respect to effective suppression of the charge recombi-
nation, increased Voc and electron lifetime. Furthermore, the dye
Z4 with bilateral extension of PTZ with an octyloxybenzene unit
prominently displayed the best results in all parameters with Jsc
of 10.35 mA cmꢂ2, Voc of 802 mV, FF of 0.69 and
h of 5.73%. This
work provides beneficial and crucial information for developing
and designing new organic dyes for highly efficient DSSCs.
Further structural modifications of the dye Z4 to acquire even
better power conversion efficiency of DSSCs performance is in
progress.
[26] Wang ZS, Koumura N, Cui Y, Takahashi M, Sekiguchi H, Mori A, et al. Hex-
ylthiophene-functionalized carbazole dyes for efficient molecular photovol-
taic: tuning of solar-cell performance by structural modification. Chemistry of
Materials 2008;20:3993e4003.
[27] Ono T, Yamaguchi T, Arakawa H. Study on dye sensitized solar cell using novel
infrared dye. Sol Energy Materials and Solar Cells 2009;93:831e5.
[28] Hara K, Sao T, Katoh R, Furube A, Yoshihara T, Murai M, et al. Novel conjugated
organic dyes for efficient dye-sensitized solar cells. Advanced Functional
Materials 2005;15:246e52.
Acknowledgments
We are grateful to the National Natural Science Foundation
of China (20872038, 20873183, 21072064), the Natural Science
Foundation of Guangdong Province, China (10351064101000000,
S2012010010634) and the Fund from Guangzhou Science and
Technology Project, China (2012J4100003) for the financial support.
[29] Chen Z, Li F, Huang C. Organic D-
p-A dyes for dye sensitized solar cells.
Current Organic Chemistry 2007;11:1241e58.
[30] Kim S, Lee JK, Kang SO, Ko J, Yum JH, Fantacci S, et al. Molecular engineering of
organic sensitizers for solar cell applications. Journal of American Chemical
Society 2006;128:16,701e16,707.
[31] Chen R, Yang X, Tian H, Wang X, Hagfeldt A, Sun L. Effect of tetrahy-
droquinoline dyes structure on the performance of organic dye sensitized
solar cells. Chemistry of Materials 2007;19:4007e15.
References
[32] Karlsson KM, Jiang X, Eriksson SK, Gabrielsson E, Rensmo H, Hagfeldt A, et al.
Phenoxazine dyes for dye-sensitized solar cells: relationship between
molecular structure and electron life time. Chemistry e A European Journal
2011;17:6415e24.
[33] Wan ZQ, Jia CY, Duan Y, Zhou L, Zhang J, Lin Y, et al. Influence of the antennas
in starburst triphenylamine based organic dye-sensitized solar cells: pheno-
thiazine versus carbazole. RSC Advances 2012;2:4507e14.
[1] Goncalves LM, Bermudez VZ, Ribeiro HA, Mendes AM. Dye sensitized solar cell:
a safe bet for the future. Energy and Environmental Science 2008;1:655e67.
[2] Schiermeier Q, Tollefson J, Scully T, Witze A, Morton O. Electricity without
carbon. Nature 2008;454:816e23.
[3] Meyer GJ. The 2010 millennium technology grand prize: dye sensitized solar
cells. ACS Nano 2010;4:4337e43.
[34] Kim MJ, Yu YJ, Kim JH, Jung YS, Kay KY, Ko SB, et al. Tuning of spacer groups in
organic dyes for efficient inhibition of charge recombination in dye-sensitized
solar cells. Dyes and Pigments 2012;95:134e41.
[35] Wu W, Yang J, Hua J, Tang J, Zhang L, Long Y, et al. Efficient and stable dye-
sensitized solar cells based on phenothiazine sensitizer with thiophene
units. Journal of Materials Chemistry 2010;20:1772e9.
[36] Tian H, Yang X, Cong J, Chen R, Teng C, Liu J, et al. Effect of different electron
donating groups on the performance of dye-sensitized solar cells. Dye and
Pigments 2010;84:62e8.
[37] Wu TY, Tsao MH, Chen FC, Su SG, Chang CW, Wang HP, et al. Synthesis and
characterization of three organic dyes with various donors and rhodanine ring
acceptors for use in dye-sensitized solar cells. Journal of Iranian Chemical
Society 2010;7:707e20.
[38] Tian H, Yang X, Chen R, Pan Y, Li L, Hagfedlt A, et al. Phenothiazine derivatives for
efficient organic dye-sensitized solar cells. Chemical Communications 2007:3741e3.
[39] Kim SH, Kim HW, Sakong C, Namgoong J, Park SW, Ko MJ, et al. Effect of five
membered heteroaromatic linkers to the performance of phenothiazine-
based dye-sensitized solar cells. Organic Letters 2011;13:5784e7.
[40] Xie ZB, Midya A, Loh KP, Adams S, Blackwood DJ, Wang J, et al. Highly efficient
dye-sensitized solar cells using phenothiazine derivatives organic dyes.
Progress in Photovoltaics: Research and Applications 2010;18:573e81.
[41] Cao D, Peng J, Hong Y, Fang X, Wang L, Meier H. Enhanced performance of the
dye-sensitized solar cells with phenothiazine-based dyes containing double
DeA branches. Organic Letters 2011;13:610e3.
[4] O’Regan B, Grätzel M. A low-cost high efficiency solar cell based on dye
sensitized colloidal titanium dioxide films. Nature 1991;353:737e40.
[5] Chiba Y, Islam A, Watanabe Y, Komiya R, koide N, Han L. Dye sensitized solar
cells with conversion efficiency of 11.1%. Japan Journal of Applied Physics
2006;45:L638e40.
[6] Chen CY, Wang M, Li JY, Pootrakulchote N, Alibabaei L, Decoppet JD, et al.
Highly efficient light-harvesting ruthenium sensitizer for thin-film dye
sensitized solar cells. ACS Nano 2009;3:3103e9.
[7] Yella A, Lee HW, Tsao HN, Yi C, Chandiran Ak, Nazeerudin MK, et al.
Porphyrin-sensitized solar cells with cobalt(II/III)-based redox electrolyte
exceed 12 percent efficiency. Science 2011;334:629e34.
[8] Ito S, Miura H, Uchida S, Takata M, Sumiok K, Liska P, et al. High conversion-
efficiency organic dye-sensitized solar cells with
Chemical Communications 2008:5194e6.
a novel indoline dye.
[9] Ning Z, Fu Y, Tian H. Improvement of dye-sensitized solar cell: what we know and
what we need to know. Energy and Environmental Science 2010;3:1170e81.
[10] Misra A, Fischer MKR, Bauerle P. Metal-free organic dyes for dye sensitized
solar cells: from structure: property relationship to design rules. Angewandte
Chemie International Edition 2009;48:2474e99.
[11] Ooyama Y, Harima Y. Molecular designs and synthesis of organic dyes for dye-
sensitized solar cells. European Journal of Organic Chemistry 2009:2903e34.
[12] Ehret A, Stuhi L, Spilter MT. Spectral sensitization of TiO2 nano-crystalline
electrode with aggregated cyanine dyes. Journal of Physical Chemistry B
2001;105:9960e5.
[13] Ning ZJ, Tian H. Triarylamine: a promising core unit for efficient photovoltaic
material. Chemical Communications 2009:5483e95.
[14] Hagfeldt A, Coschloo G, Sun LC, Kloo L, Pettersson H. Dye sensitized solar cells.
Chemical Reviews 2010;110:6595e663.
[15] Listorti A, O’Regan B, Durrant JR. Electron transfer dynamics in dye-sensitized
solar cells. Chemistry of Materials 2011;23:3381e99.
[42] Hong Y, Liao JY, Fu JL, Kuang DB, Meier H, Su CY, et al. Performance of dye
sensitized solar cells based on novel sensitizers bearing asymmetric double
De
peA chains with arylamines as donors. Dyes and Pigments 2012;94:481e9.
[43] Orto ED, Raimondo L, Sassella A, Abbotto A. Dye-sensitized solar cells: spec-
troscopic evaluation of dye loading on TiO2. Journal of Materials Chemistry
2012;22:11,364e11,369.
[44] Wan MX, Zou YP, Tan ST, Li YF. Two thieno[3,4b]pyrazine-containing copol-
ymers: synthesis, characterization, and application in mercury ions detection.
Advanced Polymer Technology 2010;21:256e62.
[16] Shi J, Chai Z, Zhong C, Wu W, Hua J, Dong Y, et al. New efficient dyes con-
taining tert-butyl in donor for dye sensitized solar cells. Dye and Pigments
2012;95:244e51.
[45] Chen CJ, Liao JY, Chi ZJ, Xu BJ, Zhang XQ, Kuang DB, et al. Metal-free organic
dyes derived from triphenylethylene for dye-sensitized solar cells: tuning of
performance by phenothiazine and carbazole. Journal of Materials Chemistry
2012;22:8994e9005.
[17] Mann JR, Gannon MK, Fitzgibbons TC, Detty MR, Watson DF. Optimizing the
photocurrent efficiency of dye sensitized solar cells through the controlled
aggregation of chalcogenosanthylium dyes on nano-crystalline titania films.
Journal of Physical Chemistry C 2008;112:13,057e13,061.

Z. Iqbal et al. / Dyes and Pigments 96 (2013) 722e731
731
[46] Rossi U, Kriwanek J, Daehne S. Influence of the N-alkyl chain length on the
J-aggregation behavior of the cyanine dye. Journal of Fluorescence 1994;4:53e5.
[47] Lee CJ, Kim KJ, Rhee SB. The effects of ester substitution and alkyl chain length
on the properties of poly(thiophene)s. Synthetic Metals 1995;69:295e6.
[48] Park DY, Kim DH, Jang Y, Cho JH, Hwang M, Lee HS, et al. Effect of side chain
length on molecular ordering and field effect mobility in poly(3-
alkylthiophene) transistors. Organic Electronics 2006;7:514e20.
[56] Zhang G, Bai Y, Li R, Shi D, Wenger S, Zakeeruddin SM, et al. Employ a bis-
thienothiophene linkers to construct an organic chromophores for efficient
and stable dye-sensitized solar cells. Energy and Environmental Sciences
2009;2:92e5.
[57] Frisch MJ, Trucks GW, Schlegel HB, Scuseria GE, Robb MA, Cheeseman JR, et al.
Gaussian 09. Wallingford, CT: Gaussian, Inc.; 2009.
[58] Yang CJ, Chang YJ, Watanabe M, Hon YS, Chow TJ. Phenothiazine derivatives
as organic sensitizers for highly efficient dye-sensitized solar cells. Journal of
Materials Chemistry 2012;22:4040e9.
[49] Rima J, Aoun E, Hanna K. Effect of n-alkyl chain length on the complexation of
phenanthrene and 9-alkyl-phenanthrene with b-cyclodextrin. Spectrochimica
Acta Part A 2004;60:1515e21.
[59] Montanari I, Nelson J, Durrant JR. Iodide electron transfer kinetics in dye-
sensitized nanocrystalline TiO2 films. Journal of Physical Chemistry B 2002;
106:12,203e12,210.
[60] Fabregat SF, Bisquert J, Garcia BG, Boschloo G, Hagfeldt A. Influence of electrolyte
in transport and recombination in dye-sensitized solar cells studied by imped-
ance spectroscopy. Solar Energy Materials and Solar Cells 2005;87:117e31.
[61] Liao JY, Lei BX, Chen HY, Kuang DB, Su CY. Orientated hierarchical single
crystalline anatase TiO2 nanowire arrays on Ti-foil substrate for efficient
flexible dye-sensitized solar cells. Energy and Environmental Science 2012;5:
5750e7.
[62] Xu MF, Li RZ, Pootrakulchote N, Shi D, Guo J, Yi ZH, et al. Tuning the energy
levels of organic sensitizers for high-performance dye-sensitized solar cells.
Journal of Physical Chemistry C 2008;12:9770e6.
[63] Babel A, Jenekhe SA. Alkyl chain length dependence of the field-effect carrier
mobility in regioregular poly(3-alkylthiophene)s. Synthetic Metals 2005;148:
169e73.
[50] Kinji K, Kyun PL, Shinya M, Kenji I, Yashukiyo U. Alkyl substituents effect on J-
or H-aggregate formation of bisazomethine dyes. Dyes and Pigments 2011;92:
783e8.
[51] Qin YC, Peng Q. Ruthenium sensitizers and their applications in dye sensitized
solar cells. International Journal of Photoenergy 2012:1e21.
[52] Yang HY, Yen YS, Chou YC, Lin JT. Organic dyes containing coplanar diphenyl
substituted dithienosilole core for efficient dye-sensitized solar cells. Journal
of Organic Chemistry 2010;75:4778e85.
[53] Qin CJ, Islam A, Han L. Panchromatic donor-acceptor sensitizers based on 4H-
cclopenta[2,1-b:3,4-b0]dithiophene-4-one as
a
strong acceptor for dye-
sensitized solar cells. Dyes and Pigments 2012;94:553e60.
[54] Grätzel M. Photo-electrochemical cells. Nature 2001;414:338e44.
[55] Ito S, Zakeeruddin SM, Humphery BR, Liska P, Charvet R, Comte P, et al. High-
efficiency organic dye-sensitized solar cells controlled by nanocrytalline TiO2
electrode thickness. Advanced Materials 2006;18:1202e5.