92-51-3Relevant articles and documents
Hawkes,G.E. et al.
, p. 1709 - 1716 (1976)
Hydrogenation of biphenyl and isomeric terphenyls over a Pt-containing catalyst
Kalenchuk,Koklin,Bogdan,Kustov
, p. 1208 - 1212 (2017)
Catalytic hydrogenation of benzene, biphenyl, and ortho-, metha-, and para-isomers of terphenyl over a 3 wt.% Pt/C at 180 °C and 70 atm was studied. The directions of hydrogenation of each substrate were revealed. Relationships between structures of the substrate and hydrogen consumption rates were found. It was shown that hydrogenation rate decreases on going from benzene to terphenyl and with increasing degree of the substrate hydrogenation. Hydrogenation rate of terphenyl isomers decreases in the following order: p-terphenyl > > m-terphenyl > o-terphenyl.
ArF Excimer Laser-induced Selective Coupling of Cycloalkanes: Photochemical Reaction at the Absorption Edge
Ouchi, Akihiko,Yabe, Akira,Inoue, Yoshihisa,Daino, Yoshihiko,Hakushi, Tadao
, p. 1669 - 1671 (1989)
Bicycloalkyls were selectively produced from the corresponding liquid phase cycloalkanes by irradiation at their absorption edge with ArF excimer laser; the photoreaction proceeded by a radical mechanism and showed a dependence of the dimerization rate on ring size.
Supported Pt-Ni bimetallic nanoparticles catalyzed hydrodeoxygenation of dibenzofuran with high selectivity to bicyclohexane
Wu, Pengyu,Cai, Chun
supporting information, p. 234 - 238 (2021/07/10)
Catalytic hydrodeoxygenation (HDO) is one of the most effective methods to upgrade the oxygen-containing compounds derived from coal tar to valuable hydrocarbons. Herein, an efficient bimetallic catalyst Pt1Ni4/MgO was prepared and applied in the HDO of dibenzofuran (DBF). High yield (95%) of the desired product bicyclohexane (BCH) was achieved at 240 °C and 1.2 MPa of H2. Superior catalytic performance could be ascribed to the “relay catalysis” of Pt sites and Ni sites, and the reaction pathway is proposed as well. Scale-up experiment and recyclability test were also performed, which demonstrated the recyclability and promising potential application of Pt1Ni4/MgO.
Bulk hydrotreating MonW12-nS2 catalysts based on SiMonW12-n heteropolyacids prepared by alumina elimination method
Kokliukhin,Nikulshina,Mozhaev,Lancelot,Lamonier,Nuns,Blanchard,Bugaev,Nikulshin
, p. 26 - 37 (2020/08/21)
A series of unsupported mono- and bimetallic MonW12-nS2 catalysts were synthesized by alumina elimination from supported MonW12-nS2/Al2O3 samples using acid etching. Alumina supported catalysts have been in turn prepared by using monometallic H4SiMo12O40 and H4SiW12O40 heteropolyacids (HPAs), their mixture with Mo/W atomic ratio equal to 1/11 and 3/9, and mixed bimetallic H4SiMo1W11O40 and H4SiMo3W9O40 HPAs. All catalysts were characterized by N2 adsorption, temperature-programmed reduction (TPR), X-ray photoelectron spectroscopy (XPS), high-resolution transmission electron microscopy (HRTEM), time-of-flight secondary ion mass spectrometry (ToF-SIMS), extended X-ray absorption fine structure (EXAFS) spectroscopy and powder X-ray diffraction (XRD) and their performance were evaluated in simultaneous hydrodesulfurization (HDS) of dibenzothiophene (DBT) and hydrogenation (HYD) of naphthalene. The etching process led to a successful removal of all the support and of the partially sulfided species, with sulfidation degrees of both Mo and W above 90 % on the final bulk solids. The active phase also underwent a rearrangement, as higher average length and stacking were measured on the bulk catalysts than on the original supported ones. Mixed MoWS2 phase was evidenced in all solids, prepared from mixed HPAs (MonW12-nS2) or from the mixture of monometallic HPAs (RefMonW12-nS2), by EXAFS and ToF-SIMS, with however a larger quantity on the MoW solids. It seems that the mixed MoWS2 phase observed on the supported MoW catalysts is maintained through the etching process, while on RefMonW12-nS2 the mixed phase, observed in a much lesser extent in the corresponding supported catalyst, could result from the aggregation of the monometallic slabs. MonW12-nS2 catalysts were found more effective than the monometallic catalysts and than the corresponding RefMonW12-nS2, in both dibenzothiophene hydrodesulfurization and naphthalene hydrogenation, which was related to the presence of the mixed phase maintained through the etching of the support.
HYDRODESULFURIZATION CATALYST WITH A ZEOLITE-GRAPHENE MATERIAL COMPOSITE SUPPORT AND METHODS THEREOF
-
Paragraph 0152; 0162, (2021/01/29)
A hydrodesulfurization catalyst, which includes (i) a catalyst support including a zeolite doped with 0.1 to 0.5 wt. % of a graphene material, based on a total weight of the catalyst support, (ii) 5 to 20 wt. % of molybdenum, based on a total weight of the hydrodesulfurization catalyst, and (iii) 1 to 6 wt. % of a promoter selected from the group consisting of cobalt and nickel, based on a total weight of the hydrodesulfurization catalyst. The molybdenum and the promoter are homogeneously disposed on the catalyst support. A method of producing the hydrodesulfurization catalyst via incipient wetness impregnation techniques, and a method for desulfurizing a hydrocarbon feedstock with the hydrodesulfurization catalyst are also provided.
