Heterogeneous ceria catalyst with water-tolerant Lewis acidic sites for one-pot synthesis of 1,3-diols via prins condensation and hydrolysis reactions

Article abstract of DOI:10.1021/ja310498c

The use of a heterogeneous Lewis acid catalyst, which is insoluble and easily separable during the reaction, is a promising option for hydrolysis reactions from both environmental and practical viewpoints. In this study, ceria showed excellent catalytic activity in the hydrolysis of 4-methyl-1,3-dioxane to 1,3-butanediol in 95% yield and in the one-pot synthesis of 1,3-butanediol from propylene and formaldehyde via Prins condensation and hydrolysis reactions in an overall yield of 60%. In-depth investigations revealed that ceria is a water-tolerant Lewis acid catalyst, which has seldom been reported previously. The ceria catalysts showed rather unusual high activity in hydrolysis, with a turnover number (TON) of 260, which is rather high for bulk oxide catalysts, whose TONs are usually less than 100. Our conclusion that ceria functions as a Lewis acid catalyst in hydrolysis reactions is firmly supported by thorough characterizations with IR and Raman spectroscopy, acidity measurements with IR and ³¹P magic-angle-spinning NMR spectroscopy, Na⁺/H ⁺ exchange tests, analyses using the in situ active-site capping method, and isotope-labeling studies. A relationship between surface vacancy sites and catalytic activity has been established. CeO₂(111) has been confirmed to be the catalytically active crystalline facet for hydrolysis. Water has been found to be associatively adsorbed on oxygen vacancy sites with medium strength, which does not lead to water dissociation to form stable hydroxides. This explains why the ceria catalyst is water-tolerant.

Full text of DOI:10.1021/ja310498c

Article
pubs.acs.org/JACS
Heterogeneous Ceria Catalyst with Water-Tolerant Lewis Acidic Sites
for One-Pot Synthesis of 1,3-Diols via Prins Condensation and
Hydrolysis Reactions
Yehong Wang, Feng Wang,* Qi Song, Qin Xin, Shutao Xu, and Jie Xu*
State Key Laboratory of Catalysis, Dalian National Laboratory for Clean Energy, Dalian Institute of Chemical Physics, Chinese
Academy of Sciences, Dalian 116023, P. R. China
*
S Supporting Information
ABSTRACT: The use of a heterogeneous Lewis acid catalyst,
which is insoluble and easily separable during the reaction, is a
promising option for hydrolysis reactions from both environ-
mental and practical viewpoints. In this study, ceria showed
excellent catalytic activity in the hydrolysis of 4-methyl-1,3-
dioxane to 1,3-butanediol in 95% yield and in the one-pot
synthesis of 1,3-butanediol from propylene and formaldehyde via
Prins condensation and hydrolysis reactions in an overall yield of
6
0%. In-depth investigations revealed that ceria is a water-tolerant
Lewis acid catalyst, which has seldom been reported previously.
The ceria catalysts showed rather unusual high activity in
hydrolysis, with a turnover number (TON) of 260, which is
rather high for bulk oxide catalysts, whose TONs are usually less
than 100. Our conclusion that ceria functions as a Lewis acid catalyst in hydrolysis reactions is firmly supported by thorough
31
characterizations with IR and Raman spectroscopy, acidity measurements with IR and P magic-angle-spinning NMR
+
+
spectroscopy, Na /H exchange tests, analyses using the in situ active-site capping method, and isotope-labeling studies. A
relationship between surface vacancy sites and catalytic activity has been established. CeO (111) has been confirmed to be the
2
catalytically active crystalline facet for hydrolysis. Water has been found to be associatively adsorbed on oxygen vacancy sites with
medium strength, which does not lead to water dissociation to form stable hydroxides. This explains why the ceria catalyst is
water-tolerant.
INTRODUCTION
and leading to malfunction of the Lewis acidic sites. However, it
■
14
has been found that NbO tetrahedra, which are Lewis acidic
4
Unsupported crystalline bulk oxides characterized with high
1
−6
7,8
sites on the Nb O ·nH O surface, form NbO −H O adducts in
2
5
2
4
2
activity, selectivity, and stability, such as MgO,
VOx,
9
−11
12,13
14
the presence of water. Some of the adducts can still function as
effective Lewis acidic sites for allylation and isomerization
reactions in water. Corma and co-workers have reported a
series of works on reactions in water catalyzed by Sn-based
MoO3,
Fe O ,
2 3
and Nb O , have been employed as
2
5
catalysts in many organic transformations. Ceria (CeO ) and
2
ceria-based materials have been used as active species,
promoters, and/or supports of heterogeneous catalysts. The
wide application of ceria is driven by its ability to store and
release oxygen (by creating oxygen vacancy sites) because of
the easily accessible redox cycle of cerium ions (Ce ⇄ Ce )
at reaction temperatures below 200 °C.
it is considered that under mild reaction conditions, surface
oxygen is less mobile and firmly held in lattice matrix.
Therefore, organic reactions taking place under these
17−20
zeolites.
Their results show that Lewis acidic sites can
practically be effective in water. Other examples, such as metal
21−28
29−32
33−36
3
+
4+
triflates,
metal chlorides,
and boron-based salts,
1
5,16
have also been claimed to be water-tolerant reusable catalysts,
but none of them has been known to be catalytically active in
hydrolysis reactions.
On the other hand,
1
,3-Butanediol is used as comonomer in some polyurethane
15
and polyester resins, taking advantage of its good resistance,
conditions may involve only the acid−base properties of ceria.
3
7,38
dyeability, and flexibility.
It can be prepared via
39
Hydrolysis reactions are greatly significant in both organic
chemistry and industrial production, and are usually catalyzed
by homogeneous or supported Brønsted acids in aqueous
acetaldehyde condensation and hydrogenation. Propylene
and formaldehyde (P-F), which are readily available starting
materials, can be converted to 1,3-butanediol through a tandem
reaction involving Prins condensation of P-F to 4-methyl-1,3-
media. Homogeneous Lewis acid catalysts, such as AlCl and
BF , decompose or are irreversibly deactivated in water.
3
3
Generally, water is dissociatively adsorbed on Lewis acidic
sites or oxygen vacancy sites of oxides to produce hydroxide
and a proton, irreversibly reforming the oxide surface structure
Received: October 24, 2012
Published: December 10, 2012
©
2012 American Chemical Society
1506
dx.doi.org/10.1021/ja310498c | J. Am. Chem. Soc. 2013, 135, 1506−1515

Journal of the American Chemical Society
Article
dioxane (4MD) (Figure 1a) followed by hydrolysis of 4MD to
stirred for 1 h at 70 °C, and the solid was filtered out and washed with
water until neutral (500 mL). The treatment was repeated three times
to increase the ion-exchange level. Finally, the ion-exchanged sample
1
,3-butanediol (Figure 1b). Prins condensations are known to
+
was dried in an oven at 100 °C for 12 h. The H /ceria-C sample was
+
obtained by exchanging Na /ceria-C with a 1.0 M NH NO solution
4
3
(
4
two exchanges at 70 °C for 1 h) followed by calcination at 500 °C for
42
h. Water-treated CeO was prepared by thermal treatment of a
2
certain amount of fresh CeO in an autoclave at 180 °C for 1 h. The
2
sample was dried at 120 °C before using.
Hydrolysis of 4-Methyl-1,3-dioxane. Typically, 4MD (0.16 mL,
.5 mmol), catalyst (0.1 g), water (1.0 mL), and a magnetic stir bar
1
were loaded into a Teflon-lined autoclave reactor. The reactor was
sealed and placed in a preheated red copper mantle at the desired
temperature. Seven reactions could be conducted simultaneously in
order to achieve parallel reaction conditions. Each reaction was
continued for the desired time and then terminated by natural cooling
to ambient temperature, after which samples were acquired for
analysis. A 1% H SO solution (1 mL) was used as a catalyst. For
2
4
comparison, 0.1 g of Sc(OTf) with 1.5 mmol of sodium dodecyl
3
4
3
sulfate (SDS) surfactant was used as catalyst. The 4MD conversion
and 1,3-butanediol selectivity were determined by normalizing the gas
chromatography (GC) integration area since 4MD and 1,3-butanediol
have similar coefficient factors in GC analysis. Product yields were
calculated by multiplying the conversion by the selectivity.
Figure 1. (a) Prins condensation of propylene and formaldehyde (P-
F) to 4MD. (b) Hydrolysis of 4MD to 1,3-butanediol. (c) One-pot
method reported here for the synthesis of 1,3-butanediol from P-F
over a heterogeneous ceria catalyst.
Kinetic Analysis of 4MD Hydrolysis. Kinetic runs were carried
out in the hydrolysis of 4MD at temperatures of 120, 130, 140, and
be catalyzed by both homogeneous and heterogeneous
−1
1
50 °C. The initial concentration of 4MD was 1.29 mol L in all
3
8
Brønsted or Lewis acids. Although the hydrolysis of
substituted 1,3-dioxanes has been studied, only homogeneous
or supported Brønsted acids have been reported to be active for
reactions. The stirring speed was maintained at >350 rotations/min to
eliminate mass transfer limitations.
One-Pot Synthesis of 1,3-Butanediol. Formaldehyde (38%
formalin, 0.42 mL, 6.0 mmol of formaldehyde), catalyst (0.1 g), water
(1.0 mL), and a magnetic stir bar were loaded into a Teflon-lined
autoclave reactor. The reactor was then sealed and placed in a
preheated red copper mantle at the desired temperature. Propylene
4
0,41
the conversion.
The use of a heterogeneous Lewis acid
catalyst, which is insoluble and easily separable from the
reaction, is a promising option for this hydrolysis reaction from
both environmental and practical viewpoints.
(99.99%) was supplied from a cylinder and charged into the reactor to
Here we report that ceria can highly efficiently catalyze the
hydrolysis of 4MD to 1,3-butanediol in 95% yield (Figure 1b).
This enabled us to realize the one-pot synthesis of 1,3-
butanediol from P-F in up to 60% yield (Figure 1c). Detailed
studies revealed that ceria is a water-tolerant Lewis acid catalyst
that is resistant to water, recyclable, and reusable at least four
times without loss of activity or selectivity. Since this catalytic
behavior of ceria is rather unusual, we made a great effort to
investigate the surface acidic nature of ceria. Our conclusions
regarding the ceria catalyst are firmly based on the results of IR
and Raman characterizations, acidity measurements with IR and
a pressure of 0.8 MPa. Products were analyzed by gas chromatog-
raphy−mass spectrometry (GC−MS) using an Agilent 7890A/5975C
instrument equipped with an HP-5MS column (30 m in length, 0.25
mm in diameter). Authenticated samples were used to quantify the
reactants and products.
Characterization by Diffuse-Reflectance IR Fourier Trans-
form (DRIFT) Spectroscopy. DRIFT spectra were collected on a
Bruker Tensor 27 instrument to obtain information about surface
hydroxyl groups. First, a powder sample was heated in situ in an IR cell
(
Harrick “Praying Mantis” diffuse reflectance accessory) at 180 °C in
−1
Ar (30 mL min ). The sample was then cooled to 30 °C, and a
background spectrum was recorded. After water adsorption for 10 min,
the IR spectra for water desorption at different temperatures were also
recorded. For data collection, the sample was cooled to 30 °C before
the measurement.
3
1
+
+
P magic-angle-spinning (MAS) NMR spectroscopy, Na /H
exchange tests, analyses using the in situ active-site capping
method, and isotope-labeling studies.
Characterization by Pyridine-Adsorption IR Analysis. Quan-
tification of acidity by the pyridine-adsorption IR method was
conducted on a Bruker 70 IR spectrometer. The sample was pressed
into a self-supporting disk (13 mm diameter, 25−27.7 mg) and placed
in a homemade IR cell attached to a closed glass-circulation system.
Prior to pyridine adsorption, the sample disk was pretreated by heating
EXPERIMENTAL SECTION
Chemicals and Reagents. All chemicals were of analytical grade
and used as purchased without further purification. Most of chemicals
were purchased from J&K Chemicals. (NH ) [Ce(NO ) ] and
■
4
2
3 6
Ce(NO ) ·6H O were purchased from Aladdin Chemicals.
3
3
2
−3
at 150 °C for 1 h in vacuum (pressure <10 Pa) and then cooled to
Preparation of Ceria. The ceria-A sample was obtained by
calcination of (NH ) [Ce(NO ) ] at 650 °C in air for 2 h, and ceria-B
3
0 °C. After a spectrum was collected, the sample disk was exposed to
4
2
3 6
pyridine vapor. IR spectra of the chemisorbed pyridine were recorded
after evacuation at 150 °C for 0.5 h (pressure <1.0 × 10− Pa) to
eliminate physically adsorbed pyridine. Spectra were collected after
cooling to 30 °C. The calculation of the number of Lewis acidic sites
was provided by the Catalysis Society of Japan. The ceria-C sample
was prepared by a conventional precipitation method. Briefly, 5.0 g of
Ce(NO ) ·6H O was dissolved in 100 mL of Millipore-purified water
3
3
3
2
(
18 mΩ·cm), and the solution was adjusted to pH 11.0 by the addition
44
was based on the following formula:
of NH OH (3.4 M) under magnetic stirring at room temperature. The
4
resulting gel mixture was washed with pure water, dried in an oven at
2
C = 1.42 × IA × R /W
1
00 °C for 12 h, and calcined at 500 °C in air for 4 h.
+ +
−1
Preparation of Na /Ceria-C, H /Ceria-C, and Water-Treated
where C is the concentration [mmol (g of catalyst) ], IA is the
integrated absorbance of the L band (cm ), R is the radius of the
+
−1
CeO . The Na /ceria-C sample was prepared using an ion-exchange
2
14
method taken from the literature. Typically, 2.0 g of ceria-C was
catalyst disk (cm), and W is the mass of the disk (mg).
Coadsorption of Pyridine and Water and IR Character-
ization. The coadsorption of pyridine with water was carried out on a
added to 40 mL of a 1.0 M NaNO solution. The suspended mixture
3
was adjusted to pH 10 using 0.5 M NaOH solution. The mixture was
1
507
dx.doi.org/10.1021/ja310498c | J. Am. Chem. Soc. 2013, 135, 1506−1515

Journal of the American Chemical Society
Article
Thermo Scientific Nicolet iS10 FTIR spectrometer in absorbance
mode. After adsorption of pyridine, water vapor (∼1 Torr) was
introduced into the IR cell. Spectra for adsorption of water for 1, 3,
and 5 min at 30 °C were then collected.
that with ceria-A (26%). These results indicate that ceria
catalysts prepared by a particular method are more active and
selective for 4MD hydrolysis than other catalysts under reaction
conditions that need further optimization.
Optimization of the reaction conditions focused on the ceria-
C catalyst in order to achieve a higher yield of 1,3-butanediol.
Figure 3a shows the catalytic results at temperatures of 110−
200 °C. The 4MD conversion increased rapidly from 2% at 110
°C to 68% at 150 °C and then to 90% at 200 °C. The 1,3-
butanediol selectivity increased from 80% at 110 °C to 98% at
Acidity Measurement by 31P NMR Spectroscopy with
Trimethylphosphine as a Probe Molecule. A special device was
4
5
designed to carry out the online treatment of samples. In this
apparatus, samples were dehydrated typically at 120 °C and at a
−
3
pressure <10 Pa for 10 h before adsorption. After dehydration, 20
kPa trimethylphosphine (TMP) (Sigma-Aldrich) was introduced, and
the system was kept for 30 min at room temperature and then
degassed at 50 °C for 15 min to remove most of the physical
adsorbates from the surface. Finally, the samples were placed in situ
into an NMR rotor, sealed, and transferred to the spectrometer
without exposure to air. Such handling of the samples avoided
1
30 °C and then leveled off at 98% with a temperature increase
to 200 °C. This behavior is typical for endothermic reactions.
The reaction enthalpy (ΔH) at 25 °C was calculated to be 85
−1
31
kJ·mol . Further optimization of the reaction time was
conducted at 180 °C (Figure 3b). The 1,3-butanediol selectivity
was close to 99% throughout the course of the reaction. The
4MD conversion constantly increased to 94% after 12 h and
leveled off at 95% after 20 h, suggesting that the hydrolysis
equilibrium was established.
oxidation of TMP and also its toxicity. P MAS NMR spectra with
high-power proton decoupling were recorded at room temperature on
a Bruker Avance III 600 MHz spectrometer using a 4 mm MAS probe
with a resonance frequency of 242.9 MHz. A total of 1024 scans were
π
accumulated with a / pulse width of 1 μs and a recycle delay of 4 s.
4
Samples were spun at 12 kHz, and chemical shifts were referenced to
8
5% H PO . For the determination of quantitative results, all of the
3 4
Coadsorption of Pyridine with Water. We employed
samples were weighed, and the spectra were calibrated by measure-
pyridine-adsorption IR characterization to probe the surface
ments on a known amount of (NH ) HPO performed under the
4
2
4
−1
acidity of ceria-C at 180 °C. The band at ∼1540 cm , which is
same conditions.
usually assigned to Brønsted acidic sites, was not found in the
Raman Characterization. Raman spectra were recorded on a
micro-Raman spectrometer (Renishaw) equipped with a CCD
detector using a He/Ne laser with a wavelength of 514 nm.
spectrum of fresh CeO pretreated at 180 °C (Figure 4a). Two
2
1
−
significant bands at 1440 and 1600 cm were observed, both
attributed to coordinatively bound pyridine on Lewis acidic
46−50
RESULTS AND DISCUSSION
sites,
indicating that the ceria surface is predominantly
■
−1
covered by Lewis acidic sites. The band at 3070 cm is due to
the C−H vibration of adsorbed pyridine. After adsorption of
water on ceria for 1, 3, and 5 min (Figure 4b−d, respectively),
Catalyst Screening Tests and Optimization of the
Reaction Conditions. To achieve a one-pot synthesis of 1,3-
butanediol, the priority was to develop a catalyst that could
efficiently hydrolyze the diether bonds of 4MD (Figure 1b),
which had not been previously reported over heterogeneous
catalyst. We tested a variety of catalysts in the hydrolysis of
−1
the IR spectra changed. The band at 1440 cm broadened and
shifted to lower wavenumber. A shoulder band at 1430 cm− is
assigned to a complex of water and pyridine. The band at 1470
1
−
1
4
MD in water (Figure 2). These catalysts have been tested in
cm can be assigned to hydrogen-bonded pyridine or
coordinatively bonded pyridine. The weak, broad bands
−1
centered at 1540 and 1601 cm and the strong band centered
−1
at ∼3200 cm are probably due to physically adsorbed water.
We thus conclude that in the presence of water, Lewis acidic
sites are still present. The surface density of Lewis acidic sites
−1
was calculated to be 0.054 mmol g based on the band at 1440
−1
44
−1
cm . The surface density of Ce cations was 0.883 mmol g
2
−1
based on the specific surface area of 67 m g with the
47
assumption of CeO (111) crystalline facets. Therefore, it is
2
roughly estimated that one out of every 16 Ce sites acts as a
Lewis acidic site. The turnover number (TON) for ceria at 180
°
C was 260, which is rather high for bulk oxide catalysts, whose
TONs are usually less than 100, and much higher than the
TON of 197 obtained over a Nb O ·nH O catalyst in the same
2
5
2
reaction.
Acidity Measured by Solid-State 31P MAS NMR
Spectroscopy. TMP has been employed to probe Brønsted
Figure 2. Catalyst screening tests in 4MD hydrolysis to 1,3-butanediol.
5
1,52
and Lewis acidity in zeolites and other materials.
The
interaction of TMP with bridging hydroxyl groups in zeolites
leads to protonation of the probe molecules. 31P MAS NMR
investigations have shown that the signal of protonated TMP
Prins condensation, but few of them have been employed in
hydrolysis. Typical basic catalysts (MgO and NaY), Brønsted
acids (H SiW O , H PW O , H-β, and H-MOR), Lewis
occurs at −3 to −5 ppm, corresponding to the Brønsted acidic
4
12 40
3
12 40
2
−
51−53
acids (Nb O , ZSM-22, and SO /ZrO ), and mineral acids
sites.
From Figure 5, the signals at −19.3 ppm can be
2
5
4
2
(
H SO ) were active but afforded a 1,3-butanediol yield of less
ascribed to TMP adsorbed on Lewis acidic sites of the CeO
2
4
2
+
than ∼30%. A 1,3-butanediol yield of 40% was achieved over a
water-tolerant Lewis acid catalyst, Sc(OTf) , indicating that
and Na -exchanged CeO samples. No resonances in the range
2
43
of −3 to −5 ppm due to interactions with Brønsted acid sites
3
the hydrolysis reaction can be catalyzed by a Lewis acid catalyst.
Ceria-C gave the best result, a 43% yield of 1,3-butanediol,
which is comparable to that with ceria-B (41%) and better than
were observed. Quantification results showed that fresh CeO
2
+
and Na -exchanged CeO had almost identical densities of
2
−1
Lewis acidic sites (0.065 and 0.063 mmol g , respectively),
1
508
dx.doi.org/10.1021/ja310498c | J. Am. Chem. Soc. 2013, 135, 1506−1515

Journal of the American Chemical Society
Article
Figure 3. (a) Effect of reaction temperature on the catalytic performance of CeO (ceria-C) in 4MD hydrolysis. (b) Time-on-stream profile at 180
2
°C.
Catalyst Stability. The ceria catalyst could be filtered out
from the reaction mixture and reused. The catalytic activities
were comparable to those for the fresh catalyst after being
recycled four times (Figure 6). This result indicates that ceria is
Figure 4. Pyridine-adsorption IR spectra of ceria-C at 180 °C (a)
without and (b−d) with water adsorption for (b) 1, (c) 3, and (d) 5
min.
Figure 6. Reusability of ceria-C in the hydrolysis of 4MD to 1,3-
butanediol.
a stable heterogeneous catalyst even in aqueous media. In many
cases, however, water adsorption is an unavoidable process,
since water is present as either a reactant or a spectator. The
water−ceria interaction has been a heated topic of discussion
because of its importance in understanding the catalytic
54−58
behavior of ceria.
Coordinatively unsaturated surface Ce
cation sites may cause water to be (i) associatively adsorbed as
a proton and hydroxide with charge deviation or (ii) dissociated
as a separated proton bound to a surface oxygen atom and
hydroxide bound to cerium with charge transfer. Case (ii) is the
common water−ceria interaction behavior under hydrothermal
conditions at high temperature, which reforms ceria into a
proton- and hydroxide-covered surface, resulting in the
irreversible change in the surface acid−base properties.
However, IR characterization of pyridine adsorption showed
that ceria-C after water treatment at 180 °C followed by
vacuum drying had nearly identical Lewis acidic sites as fresh
ceria-C (Figure 4a,b), implying that the ceria−water interaction
belongs to case (i), associative adsorption. In our reaction, the
3
1
+
F
i
g
u
r
e
5
.
P
M
A
S
N
M
R
s
p
e
c
t
r
a
o
f
T
M
P
a
d
s
o
r
p
t
i
o
n
o
n
f
r
e
s
h
,
N
a
-
exchanged, and water-treated CeO at 180 °C.
2
indicating that such ion-exchange treatment does not reform
the surface Lewis acidity. This value is close to the value
quantified by pyridine-adsorption IR spectroscopy (0.054
−1
mmol g ). We note that even a sample treated at 180 °C in
water in an autoclave did not lose its Lewis acidity (0.065 mmol
−1
g ), which clearly indicates that the Lewis acidity is water-
tolerant. This is consistent with other characterization results
provided in the following sections.
1
509
dx.doi.org/10.1021/ja310498c | J. Am. Chem. Soc. 2013, 135, 1506−1515

Journal of the American Chemical Society
Article
water adsorption does not lead to reformation of the ceria
surface, which leaves empty sites for adsorption of dioxane and
formaldehyde.
vacancy sites. It can be seen that these sites are stable in water
at 180 °C, which is the real reaction condition, and can be
oxidized upon an increase in calcination temperature. The
combination of water-adsorption IR tests and TPD measure-
ments showed that water adsorption on ceria is fairly weak,
corresponding to associative adsorption under mild reaction
conditions.
It has been theoretically and experimentally shown that
dissociatively adsorbed water is present on ceria (111) up to
5
5,59
3
00 °C.
This implies that water desorbing over the
temperature interval 100−300 °C may belong to associatively
adsorbed water on ceria. Temperature-programmed desorption
Surface Oxygen Vacancy Sites and the Active
Crystalline Facet. In the ceria lattice, each oxygen anion is
surrounded by a tetrahedron of cerium cations located at the
(
TPD) measurements are a convenient way of characterizing
60,61
the water−ceria interaction.
An online analysis system
6
5,66
equipped with a mass spectrometer was used to monitor the
evolved gas (water, 18 amu). A profile of the 18 amu mass
signal versus the temperature of sample is plotted in Figure 7.
center of a cubic arrangement of oxygen anions.
When ceria
is heated at higher temperature in vacuum or under a reducing
atmosphere, nonstoichiometric oxides CeO2−x (0 < x < 0.5),
known as the Magneli phase, are usually obtained. As shown in
Figure 8, calcination at elevated temperature oxidizes oxygen
Figure 7. Profile of temperature-programmed desorption of water
−
1
from ceria in flowing Ar gas (30 mL min ). The numbers in circles
indicate different adsorbed water species on ceria. The inset shows
structures of the four types of surface water.
Figure 8. In situ FT-IR spectroscopic monitoring of water desorption
(
(
a−d) from ceria-C at (a) 180, (b) 200, (c) 250, and (d) 500 °C and
Two distinct peaks appear from 30 to 500 °C. To get more
information on water adsorption, the experimental profile was
fitted by a Lorentz function. The first peak contains three
deconvoluted peaks with maxima at 68 °C (peak 1 in Figure 7),
e) from ceria-C pretreated at 180 °C before water adsorption. The □
symbol indicates an oxygen vacancy site.
vacancies (decreasing x value) and accordingly decreases the
Lewis acidity. Figure 9 shows the Raman shift of the calcined
CeO samples. Two bands were observed in all of the samples.
The intense band at 460 cm is ascribed to the Raman-active
F vibrational mode of the CeO fluorite-type structure. The
weak band at 590 cm (Figure 9 inset) is associated with
9
6 °C (peak 2), and 122 °C (peak 3), corresponding to three
types of water with overlapping desorption. Peak 1 is attributed
to type-I water, which is included in the interparticle space and
2
−1
62
has no interaction with the ceria surface. Peak 2 is due to
type-II water, which interacts with surface-adsorbed water or
hydroxide through hydrogen bonding. Peak 3 is ascribed to
type-III water, which is associatively adsorbed on ceria. The
second distinct peak with a maximum at 310 °C (peak 4 in
Figure 7) is the result of dehydration of structural hydroxides,
67
2g
2
−1
6
0,62
which has been explained previously.
In the hydrolysis
reaction, only type-III water provides active protons needed for
hydrolysis. The other three types of water are either
molecularly adsorbed or dissociatively adsorbed without
apparent acidity.
Following TPD tests, we measured the in situ IR spectra of
samples calcined at 180, 200, 250, and 500 °C, respectively.
−1
The wide signals in the 3480−3600 cm range are ascribed to
the surface residual cerium oxyhydroxide sites located within
6
3
pores. Some studies on silica reported this wavenumber range
64
to correspond to geminal and triple hydroxyl groups. The
−1
adsorption at 3662 cm is attributed to saturated surface
hydroxyl groups, which are stable upon calcination at up to 500
−
1
°
C. The peak at 3630 cm is due to surface hydroxyl groups
63
neighboring oxygen vacancy sites. In this study, the signal at
Figure 9. Raman spectra (514 nm) of CeO calcined at different
2
630 cm− was used as an indicator for the presence of oxygen
1
temperatures in air.
3
1
510
dx.doi.org/10.1021/ja310498c | J. Am. Chem. Soc. 2013, 135, 1506−1515

Journal of the American Chemical Society
Article
6
8
oxygen vacancy sites. Because Raman spectroscopy with the
5
evaluated in this study to understand the active crystalline facet.
69
71,72
14 nm laser line provides only surface information for CeO2,
On the basis of the reported methods,
we prepared uniform
the oxygen vacancy sites detected by Raman spectroscopy
crystalline nanopolyhedra, nanorods, and nanocubes of CeO2.
X-ray diffraction (XRD) and transmission electron microscopy
(TEM) characterizations indicated that our results well-
repeated those in the literature (Figures S4 and S5 in the
Supporting Information). These samples selectively expose
(111) and (100), (110) and (100), and (100) facets,
respectively (Table 1). On the basis of theoretical calculations
predominantly exist on the CeO surface. The ratio of the
2
−1
integrated peak areas under the bands at 590 and 462 cm
(
A590/A462) can be used to quantify the relative surface
69,70
concentration of oxygen vacancy sites.
The decrease in
the A590/A462 ratio with increasing calcination temperature
indicates a gradual decrease in the number of surface oxygen
vacancy sites and an overall decrease in the number of Lewis
acidic sites (Figure 10). It is apparent that the concentration of
72
on surface oxygen vacancy sites of each crystalline phase, we
computed the total number of surface oxygen atoms (atoms
−2
nm ) for each sample, which decreased in the sequence
nanopolyhedron > nanocube > nanorod. Multiplying the total
number of surface oxygen atoms by the specific surface area of
each sample, we found that the number of surface oxygens per
gram of ceria decreased in the sequence nanopolyhedron >
nanorod > nanocube, which is exactly the same order as we
obtained for the 1,3-butanediol yield in 4MD hydrolysis. We
infer that the active crystalline facet for the hydrolysis reaction
is the (111) facet, which is the most exposed facet for
nanopolyhedral ceria (57% exposed on the basis of the data of
Table 1). We note that the hydrolysis over ceria is less
associated with its redox properties, which is a general
consideration for high-temperature reactions (200−500 °C).
However, our correlation of surface oxygen vacancy sites with
4
MD hydrolysis is still meaningful because those sites of ceria
are created upon calcination of the cerium precursor and
remain intact during hydrolysis. The catalytic process mainly
involves polarization of oxygen-containing bonds (water and
Figure 10. Dependence of surface concentration of oxygen vacancy
sites and Lewis acidic sites of CeO on calcination temperature.
2
n+
dioxane) on vacancy sites (Ce sites). Our results agree well
with previous studies that the ceria (111) crystalline facet is
surface oxygen vacancies measured by Raman scattering and
the number of Lewis acidic sites obtained from pyridine-
adsorption IR tests change in a similar way with increasing
calcination temperature. A plot of the A590/A462 ratio against
the yield of 1,3-butanediol gives good linearity, indicating that
highly selective and active for organic reactions involving C−O
7
3−76
or O−H bond activation under mild conditions.
+
+
Na /H Exchange. Hydroxyl groups generated on the
coordinatively unsaturated cations on surface of metal oxides
are usually considered as Brønsted acidic sites when the
77
+
+
oxygen vacancy sites of CeO are catalytically active for 4MD
materials are used in water. The Na /H exchange method
has been used to study the Lewis acidic sites of a niobic oxide
2
hydrolysis to 1,3-butanediol (Figure 11).
It is known that the exposed crystalline facets of ceria, for
example, the low-index crystalline facets (100), (110), and
14
catalyst. We prepared two ceria samples to obtain a better
understanding of the active sites of the ceria catalysts and to
+
(111), have different surface concentrations of oxygen defect
verify the reliability of the IR tests. One sample, Na /ceria-C,
sites. Depending on the synthesis method, ceria with different
exposed crystalline facets can be prepared, and they were
was prepared by exchanging the possible surface Brønsted
acidity of ceria-C with Na to block Brønsted acidic sites, which
+
was confirmed by pyridine-adsorption IR analysis (Figure S6 in
+
the Supporting Information). The other sample, H /ceria-C,
+
+
was prepared by ion exchange of Na /ceria-C with NH
4
followed by calcination to remove NH and recover the surface
3
+
acidity. The catalytic performances of ceria-C, Na /ceria-C, and
H /ceria-C were compared under identical reaction conditions
+
in the hydrolysis of 4MD, and the results are shown in Figure
+
1
2. The conversion of 4MD over Na /ceria-C was slightly
lower than with ceria-C, and the selectivity remained
+
unchanged. H /ceria-C catalyzed the reaction as well as ceria-
C, indicating that the reactivity can be recovered by exchanging
+
+
Na with H . This test again confirmed that the Lewis acidic
sites of CeO play a decisive role in catalyzing the hydrolysis of
2
4
MD to 1,3-butanediol. Since 2003, Sato and co-workers have
reported a series of works investigating why ceria stands out as
an excellent catalyst among various oxides in the dehydration of
78,79
diols (especially 1,3-butanediol) to unsaturated alcohols.
Experimental results and theoretical analysis have enabled them
to conclude that surface oxygen vacancy sites play a key role in
1,3-butanediol activation. Although the hydrolysis reaction to
Figure 11. Plot of the yield of 1,3-butanediol versus the A590/A462 ratio
for samples calcined at (a) 400, (b) 550, (c) 700, and (d) 800 °C.
1
511
dx.doi.org/10.1021/ja310498c | J. Am. Chem. Soc. 2013, 135, 1506−1515

Journal of the American Chemical Society
Article
Table 1. Morphologies, Numbers of Surface Oxygen Atoms, and 1,3-Butanediol Yields over Different Types of Nanosized
a
Ceria
exposed crystalline facets
and their ratio
total number of surface oxygen atoms
S
specific number of surface oxygen
yield of 1,3-
butanediol (%)
BET
(atoms nm−
2
)
(m g−1)b
2
atoms (atoms g
−1
)
morphology
nanopolyhedron
nanorod
(111):(100) = 8:6
(110):(100) = 4:2
(100) only
(8/14) × 15.7 + (6/14) × 13.7 = 14.8
(4/6) × 9.8 + (2/6) × 13.7 = 11.1
1 × 13.7 = 13.7
63
61
33
9.3 × 1014
6.7 × 101
4.5 × 1014
73
66
49
4
nanocube
a
72 b
Data of the theoretical exposed crystalline facets and their ratio and surface oxygen concentration are referenced from literature.
Brunauer−
Emmett−Teller (BET) surface area.
was present, the 1,3-butanediol yield was comparable to that for
the reaction without DTBPy (52% in Figure 13b vs 51% in
Figure 13a, respectively). In comparison, the use of pyridine
remarkably suppressed the yield to 7% (Figure 13c). These
results indicate that (i) the interaction of water with Ce cation
sites does not block the Lewis acidity and (ii) Lewis acidic sites
are accessible active sites for 4MD hydrolysis even in water.
This reinforces our conclusion that ceria is a water-tolerant
Lewis acid catalyst.
Kinetic Analysis and Mechanism of Hydrolysis. The
reaction kinetics of the 4MD hydrolysis was studied at
temperatures of 120−150 °C (Figure 14). The mass-transfer
Figure 12. Results for hydrolysis of 4MD to 1,3-butanediol catalyzed
+
+
by ceria-C, Na /ceria-C, and H /ceria-C.
1
,3-butanediol is obviously different from the dehydration
reactions, we believe that at the molecular level, 1,3-butanediol
may accommodate itself to an energetically favorable state on
the ceria surface, which is beneficial for 1,3-butanediol in either
80
its conversion or generation.
In Situ Capping Test. Although pyridine-adsorption IR
characterization did not show that ceria contains Brønsted
acidic sites, the interaction with water during the reaction may
generate hydroxyl moieties in the ceria if water is strongly
adsorbed on oxygen vacancy sites. We employed pyridines for
competitive adsorption with the reactants to probe the acidic
Figure 14. (a) Kinetic analysis of the hydrolysis of 4MD at (
(
■
) 120,
8
1,82
▲) 130, (●) 140, and (★) 150 °C. (b) Arrhenius plot using the data
in (a). The activation energy was found to be E = 103.1 kJ·mol .
character during the reaction.
Pyridine irreversibly reacts
−1
with Lewis and Brønsted acidic sites, while 2,6-di-tert-
a
butylpyridine (DTBPy) selectively poisons Brønsted acid sites
1
7,83,84
because of steric hindrance.
Through these tests, the
catalytic nature (i.e., which acidic sites are active for catalysis)
can be clearly disclosed. The 4MD hydrolysis was performed in
the presence of pyridine or DTBPy (Figure 13). When DTBPy
resistance was eliminated by increasing the speed of agitation
until the reaction rate was not further increased. The 4MD
hydrolysis reaction is shown in eq 1:
The concentrations of water and catalyst remained essentially
constant during the reaction, allowing the dependence of the
rate on 4MD to be isolated. Thus, the rate equation could be
simplified as shown in eq 2:
d[4MD]
α
β
γ
β
−
= k[cat] [4MD] [H O] = k [4MD]
2
obs
dt
(2)
where [cat], [4MD], and [H O] are the catalyst, 4MD, and
2
−1
water concentrations, respectively (mol L ), k is the true
reaction rate coefficient, and kobs is the empirical pseudo-β-
order rate coefficient. The plot of [4MD] against time resulted
in a linear relationship (Figure 14a), indicating a pseudo-
zeroth-order reaction (i.e., β = 0). Thus, eq 2 could be further
simplified to eq 3:
Figure 13. GC results for hydrolysis of 4MD to 1,3-butanediol (a)
with no additive, (b) with 5% DTBPy, and (c) with 5% pyridine.
1
512
dx.doi.org/10.1021/ja310498c | J. Am. Chem. Soc. 2013, 135, 1506−1515

Journal of the American Chemical Society
Article
d[4MD]
Figures S7 and S8 in the Supporting Information). This
indicates that the two H atoms of the hydroxyls of 1,3-
butanediol originate from water. The Ce sites on the surface act
as Lewis acidic sites for substrate adsorption because they have
−
= kobs
dt
(3)
The kobs values at 120, 130, 140, and 150 °C calculated from
−6
the slopes of the plots in Figure 14a were 1.3 × 10 , 3.5 ×
an affinity for the oxygen atoms of dioxane and water, and they
−6
−6
−5
−1 −1
1
0 , 5.4 × 10 , and 1.2 × 10 mol L s , respectively. A
47,73
cause a polarization of the diether and H−OH bonds.
This
linear Arrhenius plot of ln(k ) versus 1/T was obtained
obs
proposal is well-supported by the control test in the presence of
pyridine, which competitively adsorbs on Ce sites and thus
blocks the initial substrate adsorption. A similar mechanism is
(
Figure 14b), and the activation energy (E ) was calculated to
be 103.1 kJ·mol .
A tentative reaction mechanism is thus proposed in Figure
a
−1
85
known in the retro-Aldol reaction. It is very possible that
1
5. Water is associately adsorbed on Lewis acidic sites of ceria,
some specific surface anion sites or vacancy clusters on ceria
may well accommodate 1,3-butanediol. Such a surface structure
is beneficial for the production of 1,3-butanediol as well as for
its dehydration at high temperature as reported by Ichikawa et
80
al.
One-Pot Synthesis of 1,3-Butanediol. We were further
interested in the one-pot synthesis of 1,3-butanediol from P-F.
Ceria-C catalyzed both the Prins condensation and 4MD
hydrolysis and offered a 60% yield of 1,3-butanediol, which was
the best result obtained in the study (Table 2). The other
product was 4MD with 26% yield. The reactions over other
basic (MgO) and acidic catalysts (H-β, HY, heteropoly acids
and SO42 /ZrO ) were sluggish and less selective toward 1,3-
−
2
butanediol, either generating a great amount of tetrahydro-2H-
pyran-4-ol and olefins or inefficiently catalyzing 4MD
hydrolysis. The excellent performance of the ceria catalyst is
attributed to its ability to catalyze the 4MD hydrolysis reaction.
To the best of our knowledge, this is the first report of the
synthesis of 1,3-butanediol from P-F. We note that when a
tandem reactor (one reactor for the Prins condensation and
another downstream for the hydrolysis) was used in our study,
the yield of 4MD in the first reactor reached 90% and the yield
of 1,3-butanediol in the second reached 95%. The total yield of
Figure 15. Tentative reaction mechanism for hydrolysis of 4MD to
,3-butanediol.
1
1
,3-butanediol reached 86%, which is better than that in a single
reactor. This difference may be due to the following: (i) Lower
temperature (<100 °C) is favorable for the Prins condensation.
At the high temperature that is beneficial for hydrolysis (>160
°C), side reactions take place in the Prins condensation. (ii)
Competitive activation of propylene, formaldehyde, and 4MD
on catalytic sites may decrease the catalytic activity. In either
case, the ceria catalyst plays a vital role for the 4MD hydrolysis.
The ceria catalyst was also tested in other hydrolysis
reactions, including 1,3-dioxane and epoxides to diols and
nitrile to amide (Table 3). 1,3-Dioxane was converted to 1,3-
propanediol with 84% conversion and 86% selectivity in 24 h at
where it becomes polarized. Protonation of the secondary ether
bond of 4MD leads to acetal formation and liberates the active
site for next cycle. Another water molecule that has been
activated on a Lewis acidic site then hydrolyzes the acetal to
1
,3-butanediol, formaldehyde, and water, making an active site
available for the next catalytic cycle. The proposed reaction
mechanism is supported by isotope-labeling studies in which
the hydrolysis was carried out in D O instead of H O. The
2
2
molecular ion peak of 1,3-butanediol at m/z 89 increased to m/
z 91 in for the reaction in D O (the mass spectra are shown in
2
Table 2. One-Pot Synthesis of 1,3-Butanediol from Propylene and Formaldehyde
1
513
dx.doi.org/10.1021/ja310498c | J. Am. Chem. Soc. 2013, 135, 1506−1515

Journal of the American Chemical Society
Article
a
Table 3. Hydrolysis of Dioxane, Epoxides, and Benzonitrile over the Ceria Catalyst
a
b
c
The reaction time was 24 h. Products were determined by GC−MS. 1,3-Dioxane (1.5 mmol), H O (1.0 mL), ceria-C (0.1 g). Propylene oxide
2
d
e
(
1.0 mmol), H O (1.0 mL), ceria-C (0.1 g). Epoxide (1.5 mmol), H O (10.0 mL), SDS (1.5 mmol), ceria-C (0.2 g). Benzonitrile (1.5 mmol),
2
2
H O (1.0 mL), ceria-C (0.1 g).
2
1
50 °C (entry 1). Terminal epoxides with C3, C6, and C8
AUTHOR INFORMATION
■
alkane chains were converted to the corresponding 1,2-diols in
good to high yields (entries 2−4). C6 and C8 epoxides are
immiscible in water, and therefore, SDS was needed as a
surfactant. Hydrolysis of nitriles is a way to produce amides. As
a representative reaction, benzonitrile was selectively converted
to benzylamide with >99% selectivity at moderate conversion of
Corresponding Author
wangfeng@dicp.ac.cn; xujie@dicp.ac.cn
Notes
The authors declare no competing financial interest.
4
4% (entry 5). All of these results indicate that the ceria catalyst
ACKNOWLEDGMENTS
■
can be used in various hydrolysis reactions.
We sincerely thank Prof. Dr. Justin Notestein (Northwestern
University) for help with preparation of the paper and valuable
suggestions and comments. We thank Prof. Hongchen Guo and
Dr. Cuilan Miao (State Key Laboratory of Fine Chemicals,
Dalian University of Technology) for their generous help in IR
tests. We also thank anonymous reviewers who gave valuable
suggestions and comments that have helped to improve the
quality of the manuscript. This work was supported by the
National Natural Science Foundation of China (NNSFC)
CONCLUSIONS
■
We have demonstrated that ceria is a highly active and selective
catalyst in the hydrolysis of 4-methyl-1,3-dioxane to 1,3-
butanediol in 95% yield. A high turnover number of 260 was
observed, and the catalyst can be recycled and reused.
Especially, ceria catalyzes the one-pot synthesis of 1,3-
butanediol from propylene and formaldehyde in water via
Prins condensation and 4-methyl-1,3-dioxane hydrolysis. We
carefully investigated the nature of the ceria catalyst by
spectroscopy and chemical adsorption methods. These
characterization results clearly prove that ceria contains surface
oxygen vacancy sites as Lewis acidic sites. The surface
population of vacancy sites depends on the preparation
method. A relationship between the surface oxygen vacancy
sites and the catalytic activity was established. During the
reaction, water is adsorbed on these sites with only medium
strength and does not poison these sites, which explains why
the ceria catalyst is stable in water. We believe that the present
findings will open a new vista of ceria catalysts in aqueous
reactions and greatly contribute to the understanding of other
oxides as heterogeneous catalysts. Further mechanistic studies
and applications to other reactions are underway.
(
Grants 21073184 and 21273231) and the One Hundred
Person Project of the Chinese Academy of Sciences. S.X.
acknowledges financial support from NNSFC (21103180).
REFERENCES
1) Pacchioni, G. Chem. Phys. Solid Surf. 2001, 9, 94.
2) Cavani, F.; Maselli, L.; Passeri, S.; Lercher, J. A. J. Catal. 2010,
69, 340.
3) Sheibani, H.; Amrollahi, M. A.; Esfandiarpoor, Z. Mol. Diversity
010, 14, 277.
4) Selvamani, T.; Yagyu, T.; Kawasaki, S.; Mukhopadhyay, I. Catal.
Commun. 2010, 11, 537.
(5) Reddy, M. B. M.; Ashoka, S.; Chandrappa, G. T.; Pasha, M. A.
Catal. Lett. 2010, 138, 82.
■
(
(
2
(
2
(
(
1
(
(
(
(
(
(
6) Kantam, M. L.; Mahendar, K.; Bhargava, S. J. Chem. Sci. 2010,
22, 63.
7) Gao, X. H.; Lv, X. C.; Xu, J. Kinet. Catal. 2010, 51, 394.
8) Chen, X.; Wang, F.; Xu, J. Top. Catal. 2011, 54, 1016.
9) Wang, F.; Ueda, W.; Xu, J. Angew. Chem., Int. Ed. 2012, 51, 3883.
10) Wang, F.; Ueda, W. Chem.Eur. J. 2009, 15, 742.
11) Wang, F.; Ueda, W. Chem. Commun. 2008, 3196.
12) Hermanek, M.; Zboril, R.; Medrik, I.; Pechousek, J.; Gregor, C.
J. Am. Chem. Soc. 2007, 129, 10929.
(13) Zhu, J.; Ouyang, X.; Lee, M.-Y.; Davis, R. C.; Scott, S. L.;
Fischer, A.; Thomas, A. RSC Adv. 2012, 2, 121.
ASSOCIATED CONTENT
■
*
S
Supporting Information
Catalyst preparation procedure and catalyst characterizations by
XRD, N2 adsorption, pyridine-adsorption IR spectroscopy,
electron microscopy, and mass spectrometry. This material is
available free of charge via the Internet at http://pubs.acs.org.
1
514
dx.doi.org/10.1021/ja310498c | J. Am. Chem. Soc. 2013, 135, 1506−1515

Journal of the American Chemical Society
Article
(
14) Nakajima, K.; Baba, Y.; Noma, R.; Kitano, M.; Kondo, J. N.;
(57) Yang, Z. X.; Wang, Q. G.; Wei, S. Y. Phys. Chem. Chem. Phys.
2011, 13, 9363.
Hayashi, S.; Hara, M. J. Am. Chem. Soc. 2011, 133, 4224.
(
(
15) Vivier, L.; Duprez, D. ChemSusChem 2010, 3, 654.
16) Murugan, B.; Ramaswamy, A. V. J. Am. Chem. Soc. 2007, 129,
(58) Fronzi, M.; Piccinin, S.; Delley, B.; Traversa, E.; Stampfl, C.
Phys. Chem. Chem. Phys. 2009, 11, 9188.
3
(
062.
(59) Yang, Z. X.; Wang, Q. G.; Wei, S. Y.; Ma, D. W.; Sun, Q. A. J.
Phys. Chem. C 2010, 114, 14891.
17) Corma, A. J. Catal. 2000, 191, 218.
(
(
(
(
(
(
(
18) Corma, A. J. Catal. 2003, 215, 294.
(60) Bernal, S.; Calvino, J. J.; Cifredo, G. A.; Gatica, J. M.; Omil, J. A.
P.; Pintado, J. M. J. Chem. Soc., Faraday Trans. 1993, 89, 3499.
(61) Schoiswohl, J.; Tzvetkov, G.; Pfuner, F.; Ramsey, M. G.; Surnev,
S.; Netzer, F. P. Phys. Chem. Chem. Phys. 2006, 8, 1614.
(62) Gun’ko, V. M.; Zarko, V. I.; Chuikov, B. A.; Dudnik, V. V.;
Ptushinskii, Y. G.; Voronin, E. F.; Pakhlov, E. M.; Chuiko, A. A. Int. J.
Mass Spectrom. Ion Processes 1998, 172, 161.
19) Corma, A.; Navarro, M. T.; Renz, M. J. Catal. 2003, 219, 242.
20) Corma, A.; Renz, M. Chem. Commun. 2004, 550.
21) Wiles, C.; Watts, P. ChemSusChem 2012, 5, 332.
22) Rebacz, N. A.; Savage, P. E. Ind. Eng. Chem. Res. 2010, 49, 535.
23) Kumar, A.; Rao, M. S.; Rao, V. K. Aust. J. Chem. 2010, 63, 135.
24) Aplander, K.; Ding, R.; Krasavin, M.; Lindstrom, U. M.;
Wennerberg, J. Eur. J. Org. Chem. 2009, 810.
25) Firouzabadi, H.; Iranpoor, N.; Farahi, S. J. Mol. Catal. A: Chem.
008, 289, 61.
26) Prakash, G. K. S.; Yan, P.; Torok, B.; Bucsi, I.; Tanaka, M.; Olah,
G. A. Catal. Lett. 2003, 85, 1.
(63) Badri, A.; Binet, C.; Lavalley, J. C. J. Chem. Soc., Faraday Trans.
1996, 92, 4669.
(
2
(
(64) Takei, T.; Kato, K.; Meguro, A.; Chikazawa, M. Colloids Surf., A
1999, 150, 77.
(65) Binet, C.; Daturi, M.; Lavalley, J. C. Catal. Today 1999, 50, 207.
(66) Ganduglia-Pirovano, M. V.; Hofmann, A.; Sauer, J. Surf. Sci. Rep.
2007, 62, 219.
(
27) Kobayashi, S. Synlett 1994, 689.
(
28) Vergnaud, J.; Sarazin, Y.; Strub, H.; Carpentier, J. F. Eur. Polym.
J. 2010, 46, 1093.
29) da Silva, M. L.; Figueiredo, A. P.; Cardoso, A. L.; Natalino, R.;
da Silva, M. J. J. Am. Oil Chem. Soc 2011, 88, 1431.
30) Goncalves, C. E.; Laier, L. O.; da Silva, M. J. Catal. Lett. 2011,
41, 1111.
31) Firouzabadi, H.; Iranpoor, N.; Jafarpour, M.; Ghaderi, A. J. Mol.
Catal. A: Chem. 2006, 252, 150.
(67) Shyu, J. Z.; Weber, W. H.; Gandhi, H. S. J. Phys. Chem. 1988, 92,
6.
(
(
68) Popovic,
́
Z. V.; Dohce
M. J. Raman Spectrosc. 2007, 38, 750.
69) Pu, Z.-Y.; Lu, J.-Q.; Luo, M.-F.; Xie, Y.-L. J. Phys. Chem. C 2007,
11, 18695.
70) Meng, L.; Jia, A.-P.; Lu, J.-Q.; Luo, L.-F.; Huang, W.-X.; Luo,
M.-F. J. Phys. Chem. C 2011, 115, 19789.
̌ ́ ́ ́
vic-Mitrovic, Z.; Konstantinovic, M. J.;
̌
́ ́
Scepanovic,
(
1
(
(
1
(
(
(
32) Bartoli, G.; Marcantoni, E.; Sambri, L. Synlett 2003, 2101.
33) Longuet, C.; Joly-Duhamel, C.; Ganachaud, F. Macromol. Chem.
(71) Yang, S. W.; Gao, L. J. Am. Chem. Soc. 2006, 128, 9330.
(72) Mai, H. X.; Sun, L. D.; Zhang, Y. W.; Si, R.; Feng, W.; Zhang, H.
Phys. 2007, 208, 1883.
P.; Liu, H. C.; Yan, C. H. J. Phys. Chem. B 2005, 109, 24380.
73) Laursen, S.; Combita, D.; Hungría, A. B.; Boronat, M.; Corma,
A. Angew. Chem., Int. Ed. 2012, 51, 4190.
74) Wang, X. W.; Zhao, G. M.; Zou, H. B.; Cao, Y. J.; Zhang, Y. G.;
Zhang, R. B.; Zhang, F.; Xian, M. Green Chem. 2011, 13, 2690.
75) Badri, A.; Binet, C.; Lavalley, J. C. J. Chem. Soc., Faraday Trans.
996, 92, 1603.
76) Tamura, M.; Tonomura, T.; Shimizu, K.-i.; Satsuma, A. Green
Chem. 2012, 14, 717.
77) Zaki, M. I.; Hasan, M. A.; Al-Sagheer, F. A.; Pasupulety, L.
Colloids Surf., A 2001, 190, 261.
78) Sato, S.; Takahashi, R.; Sodesawa, T.; Honda, N.; Shimizu, H.
Catal. Commun. 2003, 4, 77.
(
(
34) Ishihara, K.; Yamamoto, H. Eur. J. Org. Chem. 1999, 527.
35) Futatsugi, K.; Yamamoto, H. Angew. Chem., Int. Ed. 2005, 44,
(
1
(
484.
36) Ishihara, K.; Hanaki, N.; Funahashi, M.; Miyata, M.; Yamamoto,
H. Bull. Chem. Soc. Jpn. 1995, 68, 1721.
(
(
1
(
(
(
(
37) Sugiura, M.; Hayakawa, R. Contact Dermatitis 1997, 1997, 6.
38) Arundale, E.; Mikeska, L. A. Chem. Rev. 1952, 51, 505.
39) Shimizu, Y.; Sugimoto, S. i.; Kawanishi, S.; Suzuk, N. Chem. Lett.
1
991, 2.
40) Green, T. W.; Wuts, P. G. M. Protective Groups in Organic
Synthesis; Wiley-Interscience: New York, 1999.
(
(
(
(
41) Qi, Y.; Xu, X.; Li, N.; Fang, Y. Sep. Sci. Technol. 2011, 47, 584.
(
42) Jobic, H.; Tuel, A.; Krossner, M.; Sauer, J. J. Phys. Chem. 1996,
(79) Sato, F.; Okazaki, H.; Sato, S. Appl. Catal., A 2012, 419, 41.
100, 19545.
(80) Ichikawa, N.; Sato, S.; Takahashi, R.; Sodesawa, T. J. Mol. Catal.
(
43) Kobayashi, S.; Manabe, K. Acc. Chem. Res. 2002, 35, 209.
A: Chem. 2005, 231, 181.
(
(
44) Emeis, C. A. J. Catal. 1993, 141, 347.
45) Zhang, W.; Xu, S.; Han, X.; Bao, X. Chem. Soc. Rev. 2012, 41,
(
(
(
81) Wang, F.; Ueda, W. Top. Catal. 2008, 50, 90.
82) Wang, F.; Xu, J.; Liao, S. J. Chem. Commun. 2002, 626.
83) Marczewski, M.; Migda, A.; Marczewska, H. Phys. Chem. Chem.
192.
(
46) Parry, E. P. J. Catal. 1963, 2, 371.
Phys. 2003, 5, 423.
84) Corma, A.; Fornes
Triguero, J.; Moscotti, D. J. Catal. 1998, 179, 8.
85) Carey, F. A. Organic Chemistry, 4th ed.; McGraw-Hill, 2000; p
002.
(
47) Tamura, M.; Wakasugi, H.; Shimizu, K.; Satsuma, A. Chem.
(
́ ́
, V.; Forni, L.; Marquez, F.; Martínez-
Eur. J. 2011, 17, 11428.
(
48) Yang, N. C.; Yang, D. D. H.; Ross, C. B. J. Am. Chem. Soc. 1959,
1, 133.
49) Sasikala, R.; Shirole, A. R.; Sudarsan, V.; Kamble, V. S.; Sudakar,
C.; Naik, R.; Rao, R.; Bharadwaj, S. R. Appl. Catal., A 2010, 390, 245.
50) Tamura, M.; Shimizu, K.; Satsuma, A. Appl. Catal., A 2012, 433,
35.
51) Lunsford, J. H.; Rothwell, W. P.; Shen, W. J. Am. Chem. Soc.
985, 107, 1540.
(
1
8
(
NOTE ADDED AFTER ASAP PUBLICATION
This paper was published ASAP on January 11, 2013, with an
(
1
(
1
■
error in the units of k in the text following eq 3. The
obs
corrected version was reposted on January 14, 2013.
(
52) Kao, H. M.; Grey, C. P. J. Am. Chem. Soc. 1997, 119, 627.
(
53) Chu, Y.; Yu, Z.; Zheng, A.; Fang, H.; Zhang, H.; Huang, S.-J.;
Liu, S.-B.; Deng, F. J. Phys. Chem. C 2011, 115, 7660.
54) Molinari, M.; Parker, S. C.; Sayle, D. C.; Islam, M. S. J. Phys.
Chem. C 2012, 116, 7073.
55) Matolin, V.; Matolinova, I.; Dvorak, F.; Johanek, V.; Myslivecek,
(
(
J.; Prince, K. C.; Skala, T.; Stetsovych, O.; Tsud, N.; Vaclavu, M.;
Smid, B. Catal. Today 2012, 181, 124.
(
56) Kinch, R. T.; Cabrera, C. R.; Ishikawa, Y. J. Phys. Chem. C 2009,
113, 9239.
1
515
dx.doi.org/10.1021/ja310498c | J. Am. Chem. Soc. 2013, 135, 1506−1515